Epilog Laser Cutter

Epilog Laser Cutter

Technical specifications

• Cutting area 900 x 600 millimeters / 35.4" x 23.6" inches
• Cutting power max. 50 Watt.
• Maximum Power Consumption:

CAM

• 2D Printer driver from most CAD or ilustration software
• From PDF

Caution

• this remark should go on all pages for lasers:

The honeycomb structure of the bed of the machine is very expensive and it easily gets damaged. The quality of the cuts is only going to be good if the bed is perfectly flat and undamaged. Take good care of the honeycomb

Materials and configurations

Settings

Laser settings for common materials - Epilog 50W

Material	Cut			Raster Engraving - 600 DPI			Engraving
		Speed (%)	Power (%)	Frequency (Hz)	Speed (%)	Power (%)	Frequency (Hz)	Speed (%)	Power (%)	Frequency (Hz)
	Polypropylene - 0.5mm	45	55	5000
Polypropylene - Transparent - 0.8mm	35	50	5000	75	25	5000	80	35	5000
Polypropylene - 1.2mm	15	90	5000
Polypropylene - Black 1,2mm	30	80	5000	100	20	5000	85	30	5000
Acrylic (methacrylate/Plexiglass) - 1mm	60	70	5000	100	35
Acrylic (methacrylate/Plexiglass) - 2mm	20	90	5000
Acrylic (methacrylate/Plexiglass) - 3mm	15	90	5000	100	35
Acrylic - Transparent - 3mm	15	90	5000	100	15	5000	100	5	5000
Acrylic - Transparent - 4mm	10	95	5000
Acrylic - Transparent - 5mm	10	100	5000
Acrylic- Black color (methacrylate/Plexiglass) - 3mm	10	95	10
Acrylic (methacrylate/Plexiglass) - 6mm	5	100	5000	100	35
EVA foam (Etilvinilacetato) - 3mm	60	40	1000
EVA foam (Etilvinilacetato) Black - 10mm	35	90	1000	90	10
Paper - 3mm / 250gr	60	30	5000
Wood - Cherry/Alder/Walnut - 3mm	25	80	500	70	100
Wood - Cherry/Alder/Walnut - 6mm	10	100	500	70	100
Wood - Plywood (2mm) / Madera	15	40	500	70	100
Wood - Plywood (3mm) / Madera	10	85	2000	70	100
Wood - Plywood (4mm) / Madera	20	90	2500	75	25	500	100	10	500
Wood - Plywood (5mm) / Madera	15	90	2500	100	9	500	80	10	500
Wood - Plywood (0.5mm) / Madera	30	20	500	70	100
Wood - MDF (4mm)	20	90	500	100	20	500	70	10	500
Felt (1mm) / Fieltro	80	25	250
Fabric - Thin	80	30	500
Paper - 0.3mm	50	50	500
Paper - White - 0.6mm	80	35	500	100	10	500	100	3	500
Paper - Black finish - 1.3 mm	75	40	500	90	10
Paper - Grey - 1.5mm	75	55	500	90	10
Paper - Parchment (for lamp making)	80	10	500
Cardboard - Corrugated (4mm/1 layers)	40	45	500	100	20	500	100	10	500
Cardboard - Corrugated (5mm/2 layers)	55	45	500
Cardboard - Corrugated high res. white (6mm/1 layer	20	85	500	100	15	500	100	10	500

Note: Settings above are a good starting point. Laser cutting quality is affected by several factors including lens cleanliness, maintenance and/or aging laser tube. If you are not achieveing a cut, try to increase the power, decrease the speed or a do combination of both. Change settings with 5-10% step at a time.

Suppliers

For a supplier list take a look at this table maintained by de Fab Lab BARCELONA

Machine work flow

• If you are not going to use the computer in the Fab Lab, install the Epilog drivers in your computer (you can reach the machine inside the Fab Lab network).
• Turn on the main fume extractor in the big laser cutter switch panel.
• Turn on the small air compressor on the left hand side of the machine.
• Turn on the laser cutter (left side of the machine).
• Make sure the material you want to use is in the 'Materials and configuration' list. If it is not there, ask the Fab Lab responsible.
• Measure the size of your material board.
• From your vector editing software, once you are ready for printing and if you already installed the driver, press Ctrl+P or select 'Print'.
• Select 'Epilog Engraver' from the printer list and go to 'Printer settings' or 'Properties'.
• The laser cutter driver interface should appear. Here you can set-up the laser's power and speed according to how the vector paths in your drawing are organized (you can also print raster images).
• For a vector job:
  • In the 'General' tab, under 'Job type' select 'Vector'.
  • Set the size of the material sheet under 'Piece Size'.
  • Set to 'Vector sorting' and 'Optimize'.
  • In the 'Color mapping' tab select the check box 'Color mapping'. You should have organized your drawing in different colors if you need to do different types of jobs (for example engraving and cutting).
  • Once this is activated, you can set the power, the speed, and other parameters for every single color in your drawing. Take a look at the 'Materials and configuration' list above for the proper power/speed values according to the material you are using.
  • The list order determines the execution sequence of every type of job. You should allays engrave first and cut later. You can change the order by selecting a color and pressing the up and down arrows.
  • Once you are done with this configuration, press 'OK'.
• For a raster job:
  • You should see the parts that you want to cut/engrave fitting the material in the preview. If not, you should scale, move, rotate or change the units of the drawing to get it as you want.
  • Finalize the process with 'Print' and the file will be sent to the laser cutter.
• At the machine:
  • Open the hood and place the material on the metal bed without hitting the cutting head.
  • If the material you use is to thick (engraving bigger objects), you should lower the bed.
    • To lower the bed:
      • Press 'X/Y off' and bring the bed to the desired z position by pressing the 'up' and 'down' arrows.
  • Turn on the laser pointer 'Puntero'.
  • Set the machine head to the origin by pressing 'Restaur.' and focus the laser by pressing 'Enfocar' and 'GO/Entra'.
    • If you want to change the x/y origin follow this steps:
      • Press 'X/Y off' and bring the laser manually to the desire origin.
      • Then press 'Ajuste Inicio' and you should have now a new origin point.
• If you already sent the job to the machine you will see 'Job:job name' in the display.
• Pressing the up and down arrows will allow you to select the different jobs stored in the machine.
• Press 'GO/Entra' to start cutting/engraving.
• Press 'STOP/Salir' if something burns inside the machine or the material moves from its original position.
• Don't leave the machine unattended.

Epilog Legend 36 interface pannel

Important commands

Structure:

• http://issuu.com/fablabbcn/docs/epilog_quick_start?mode=window&backgroundColor=%23222222/
  

External links

• tv online indonesia
• Epilog Legend Series
• 'Laser cutting' in the Wikipedia
• live streaming piala dunia

Downloads

• User Manual