Difference between revisions of "Category:Rhinocam"

From Fab Lab Bcn WIKI
Jump to: navigation, search
Line 88: Line 88:
  
 
==Create Tools==
 
==Create Tools==
 +
 +
[[File:Rhinocam 20.jpg|800px]]
 +
 
To machine the above part we will now create a ½ inch (0.5”) Flat End Mill.
 
To machine the above part we will now create a ½ inch (0.5”) Flat End Mill.
  

Revision as of 12:23, 19 February 2019

work in progress

Starting RhinoCam

  • Locate the Rhinoceros 5 or Rhinoceros 6 shortcut on your desktop and double-click to launch the

application.

Alternatively, you can also click on the Windows Start button and select All Programs. Go to the program group containing Rhinoceros 5. (The name of this program group will usually be called Rhinoceros 5 or 6 unless you specified otherwise during setup.) If the installation was successful, upon launching of Rhinoceros 5 you should observe a menu called RhinoCAM 2018 in the main menu bar of Rhino. If you do not see this menu entry then please check the On-Line Help document of the product (found in the installation folder) for help with troubleshooting the installation.

  • Before we begin, let's talk a bit about the RhinoCAM display. When you run RhinoCAM for the

very first time, your screen may look at this. These windows on the left belong to plug-in modules that are currently loaded. For now, let's close all of them.

  • Launch the MILL Module

Now, let's begin by launching the RhinoCAM 2018 MILL module. 1. From the Rhino main menu bar, you will see the RhinoCAM 2018 menu item.

2. Drop-down the menu and pick MILL to load the MILL module.

3. Docked on the left you will see the Machining Browser and the Machining Objects Browser. When you first run RhinoCAM 2018, these two browsers may be docked side by side. However, you can move them anywhere on the screen that feels comfortable for you.

4. For example, let's move the Machining Objects Browser so that it displays under the Machining Browser on the left. Simply left-click and hold the title bar of the browser and drag it around on your screen.

RhinoCam interface.JPG

Setting up the strategy

To set up the stock( the whole material to be milled) follow these instructions:

Machine 1. Define the Machine and Post-processor to use.

2. Define the Machining Setup including Stock Geometry, Material and Work Zero.

3. Create and Select a Tool to use for machining.

4. Create the Machining Operations including the Feeds and Speeds, the Clearance

Plane and other Cutting Parameters. 5. Generate the toolpath.

6. Simulate the toolpath.

7. Post Process the toolpath.

8. Generate Shop Documentation.

Select the Post Processor

Rhinocam 21.jpg

Next, we'll define the Post Processor.

1. From the Program tab select, Post to display the dialogue.

2. For the Current Post Processor, select Haas from the list of available posts.

3. Then set the Posted File Extension to .nc.

4. Pick OK and notice that the Post type now appears under Machining Job in the Machining Browser.

Create Stock Geometry

Rhinocam stock.JPG

In this step, we'll define the raw stock from which to cut the part.

1. From the Program, tab select Stock and then select Box Stock from the menu to display the dialogue.

2. Under Dimensions, set the Length L to 10.0, Width W to 6.0 and Height H to 0.125. Note that the stock dimensions you enter are measured from the corner of the bounding box selected in this dialogue.

3. Pick OK and notice that the Stock type now appears under Machining Job in the Machining Browser.

4. If the stock does not display on the screen, select the Stock Visibility icon located at the base of the Machining Browser.

Create Tools

Rhinocam 20.jpg

To machine the above part we will now create a ½ inch (0.5”) Flat End Mill.

1. This will display the Create/Select Tool dialog. Select Flat Mill from the Tool Type menu at the top of the dialog.

2. Set tool Name to FlatMill-0.5 and Tool Diameter to 0.5. Under the Properties tab set Material to HSS and Tool Number to 1.

3. Switch to Feeds and Speeds tab and click Load from File.

4. From the dialog that displays, set Stock Material to Wood and Tool Material to HSS.

5. Now pick OK and the computed cut feedrate and spindle speed are transferred to the Feeds and Speeds tab of the Create/Select Tool dialog.

6. Pick Save as New Tool to save the tool. The tool is now created and listed under Tools in Session on the left side of the dialog.

7. Pick OK to close the dialog.

This category currently contains no pages or media.