Difference between revisions of "End Effector Catalogue"
| Line 3: | Line 3: | ||
[[File:End+effector+2.jpeg| thumb |ABB IRB 120 (6 Axes Robot)]] | [[File:End+effector+2.jpeg| thumb |ABB IRB 120 (6 Axes Robot)]] | ||
| − | ==Technical | + | ==Technical Data== |
| + | '''Total system power:''' 1,5 kW | ||
| − | + | '''Power input:''' 230 V, 1Ph/N/PE/50-60Hz | |
| − | + | ||
| − | + | '''Fusing:''' 16 A | |
| − | + | ||
| + | '''External control 0 - 10 Vdc for rotary speed:''' optional | ||
| + | |||
| + | '''Dimensions''' (LxWxH) : 720-780 x 340 x 790 mm | ||
| + | |||
| + | '''Hopper capacity''' 30 Litre, 44 Litre | ||
| + | |||
| + | '''Pump outlet size''' 1" GEKA PLUS | ||
| + | |||
| + | '''Filling height:''' 75 cm | ||
| + | |||
| + | '''Total weight:''' 33 kg | ||
==Health & Safety== | ==Health & Safety== | ||
| − | |||
| − | - | + | - Always use safety glass while disconnecting the hose. |
| + | |||
| + | - Never run the machine dry, at least water is needed to operate the pump otherwise damage may occur. | ||
| + | |||
| + | - Never let the material fall below the minimum material level and always keep the screw under the material. | ||
| + | |||
| + | - Never disconnect the hose when there is any pressure in the pressure gauge. | ||
| + | |||
| + | ==Machine Views== | ||
| + | |||
| + | [[File:View.jpg| 700 × 402 pixels]]<br><br> | ||
| + | |||
| + | |||
| + | 1- Motor | ||
| + | |||
| + | 2- Control system: Frequency converter with switch | ||
| + | elements, power supply inlet plug with undervoltage | ||
| + | release to prevent re-start in case of voltage interuption | ||
| + | |||
| + | 3- Hopper for wet premixed material | ||
| + | |||
| + | 4- Housing with polyurethan inlet | ||
| + | |||
| + | 5- Worm pump | ||
| + | |||
| + | 6- Pump outlet with pressure gauge | ||
| + | |||
| + | ==Operating the machine== | ||
| + | |||
| + | |||
| + | '''Connections Before Start-Up''' | ||
| − | + | Connect the main power plug to the control cabinet | |
| + | with the cable to the construction 230V/1/N/PE/50Hz | ||
| + | (3x1,5mm2). | ||
| − | + | Make sure that all cables and safety devices are functioning properly. | |
Revision as of 17:58, 26 June 2023
Technical Data
Total system power: 1,5 kW
Power input: 230 V, 1Ph/N/PE/50-60Hz
Fusing: 16 A
External control 0 - 10 Vdc for rotary speed: optional
Dimensions (LxWxH) : 720-780 x 340 x 790 mm
Hopper capacity 30 Litre, 44 Litre
Pump outlet size 1" GEKA PLUS
Filling height: 75 cm
Total weight: 33 kg
Health & Safety
- Always use safety glass while disconnecting the hose.
- Never run the machine dry, at least water is needed to operate the pump otherwise damage may occur.
- Never let the material fall below the minimum material level and always keep the screw under the material.
- Never disconnect the hose when there is any pressure in the pressure gauge.
Machine Views
1- Motor
2- Control system: Frequency converter with switch elements, power supply inlet plug with undervoltage release to prevent re-start in case of voltage interuption
3- Hopper for wet premixed material
4- Housing with polyurethan inlet
5- Worm pump
6- Pump outlet with pressure gauge
Operating the machine
Connections Before Start-Up
Connect the main power plug to the control cabinet with the cable to the construction 230V/1/N/PE/50Hz (3x1,5mm2).
Make sure that all cables and safety devices are functioning properly.
