|
|
| Line 56: |
Line 56: |
| | | | |
| | Pneumatic Push to Connect Fittings Male Straight | ∅ 8mm Tubing | | Pneumatic Push to Connect Fittings Male Straight | ∅ 8mm Tubing |
| − |
| |
| − | ==Health & Safety==
| |
| − |
| |
| − |
| |
| − | - Always use safety glass while disconnecting the hose.
| |
| − |
| |
| − | - Never run the machine dry, at least water is needed to operate the pump otherwise damage may occur.
| |
| − |
| |
| − | - Never let the material fall below the minimum material level and always keep the screw under the material.
| |
| − |
| |
| − | - Never disconnect the hose when there is any pressure in the pressure gauge.
| |
| − |
| |
| − | ==Machine Views==
| |
| − |
| |
| − | [[File:View.jpg| 700 × 402 pixels]]<br><br>
| |
| − |
| |
| − |
| |
| − | 1- Motor
| |
| − |
| |
| − | 2- Control system: Frequency converter with switch
| |
| − | elements, power supply inlet plug with undervoltage
| |
| − | release to prevent re-start in case of voltage interuption
| |
| − |
| |
| − | 3- Hopper for wet premixed material
| |
| − |
| |
| − | 4- Housing with polyurethan inlet
| |
| − |
| |
| − | 5- Worm pump
| |
| − |
| |
| − | 6- Pump outlet with pressure gauge
| |
| − |
| |
| − | ==Operating the machine==
| |
| − |
| |
| − |
| |
| − | '''Connections Before Start-Up'''
| |
| − |
| |
| − | Connect the main power plug to the control cabinet
| |
| − | with the cable to the construction 230V/1/N/PE/50Hz
| |
| − | (3x1,5mm2).
| |
| − |
| |
| − | Make sure that all cables and safety devices are functioning properly.
| |
| − |
| |
| − | '''Start-up in manual mode'''
| |
| − |
| |
| − | - Before Operating the machine check the machine state. Switch rightwards for manual mode.
| |
| − |
| |
| − | [[File:2_MAI_2PUMP_PICTOR_3D_B_Kopie.jpg| 700 × 402 pixels]]<br><br>
| |
| − |
| |
| − |
| |
| − | - '''Step 1:''' Turn on the main switch
| |
| − |
| |
| − | [[File:Onn_n_off_switch.jpg| 700 × 402 pixels]]<br><br>
| |
| − |
| |
| − |
| |
| − | - '''Step 2:''' Fill the material-hopper with wet premixed material.
| |
| − |
| |
| − | - '''Step 3:''' Turn the Forward/Reverse Switch to FWD (Start the machine by turning the mode switch from
| |
| − | 0 to FWD)
| |
| − |
| |
| − | [[File:Speed_controlle.jpg| 700 × 402 pixels]]<br><br>
| |
Revision as of 18:15, 27 June 2023
ABB IRB 120 (6 Axes Robot)
Motor Screw Extruder
Arduino Diagram
Connection to robot
elements, power supply inlet plug with undervoltage
release to prevent re-start in case of voltage interuption
3- Hopper for wet premixed material
4- Housing with polyurethan inlet
5- Worm pump
6- Pump outlet with pressure gauge
Operating the machine
Connections Before Start-Up
Connect the main power plug to the control cabinet
with the cable to the construction 230V/1/N/PE/50Hz
(3x1,5mm2).
Make sure that all cables and safety devices are functioning properly.
Vaccume end effector with single Suction cap
Required parts:
Vacuum Generator / Union / Square
Suction Cup (coval VP15NBRIF18C)
Pneumatic Push to Connect Fittings Male Straight | ∅ 8mm Tubing
