Difference between revisions of "Epilog Laser Cutter"

From Fab Lab Bcn WIKI
Jump to: navigation, search
(Settings)
(Settings)
Line 381: Line 381:
 
|style="text-align:center;"|100
 
|style="text-align:center;"|100
 
|style="text-align:center;"|20
 
|style="text-align:center;"|20
 +
|style="text-align:center;"|500
 +
|-
 +
|Wood Veneer - 0.7mm
 +
|style="text-align:center;"|85
 +
|style="text-align:center;"|55
 +
|style="text-align:center;"|500
 +
|style="text-align:center;"|70
 +
|style="text-align:center;"|5
 +
|style="text-align:center;"|500
 +
|style="text-align:center;"|100
 +
|style="text-align:center;"|5
 
|style="text-align:center;"|500
 
|style="text-align:center;"|500
 
|-
 
|-

Revision as of 19:07, 12 April 2018

Epilog Laser Cutter

Technical specifications

  • Cutting area 900 x 600 millimeters / 35.4" x 23.6" inches
  • Cutting power max. 50 Watt.
  • Maximum Power Consumption:

Health & Safety

CAM

  • 2D Printer driver from most CAD or ilustration software
  • From PDF

Caution

  • this remark should go on all pages for lasers:

The honeycomb structure of the bed of the machine is very expensive and it easily gets damaged. The quality of the cuts is only going to be good if the bed is perfectly flat and undamaged. Take good care of the honeycomb


Materials and configurations

Settings

Laser settings for common materials - Epilog 50W
Material Cut Engraving Raster Engraving - 600 DPI
Speed (%) Power (%) Frequency (Hz) Speed (%) Power (%) Frequency (Hz) Speed (%) Power (%) Frequency (Hz)
Polypropylene - 0.5mm 45 55 5000
Polypropylene - White - 0.5mm 50 50 5000 100 15 5000 100 10 5000
Polypropylene - Transparent - 0.8mm 35 50 5000 80 35 5000 75 25 5000
Polypropylene - 1.2mm 15 90 5000
Polypropylene - Black 1,2mm 30 80 5000 85 30 5000 100 20 5000
Acrylic (methacrylate/Plexiglass) - 1mm 60 70 5000 100 35
Acrylic - White - 2mm 25 90 5000 90 30 5000 100 15 5000
Acrylic (methacrylate/Plexiglass) - 2mm 20 90 5000
Acrylic (methacrylate/Plexiglass) - 3mm 15 90 5000 100 35
Acrylic - Transparent - 3mm 15 90 5000 100 5 5000 100 15 5000
Acrylic - Transparent/Matt - 3mm 15 90 5000 100 10 5000 100 15 5000
Acrylic - White - 3mm 15 88 5000 100 10 5000 100 15 5000
Acrylic - Transparent white film - 3mm 15 90 5000 100 5 5000 100 15 5000
Acrylic - Black/Semi-Transparent - 3mm 15 90 5000 100 5 5000 100 15 5000
Acrylic - Transparent - 4mm 10 95 5000
Acrylic - Transparent - 5mm 10 100 5000 100 5 5000 100 8 5000
Acrylic- Black color (methacrylate/Plexiglass) - 3mm 10 95 10
Acrylic (methacrylate/Plexiglass) - 6mm 5 100 5000 100 35
Acrylic - Transparent/Matt - 6mm 7 100 5000 100 15 5000 100 8 5000
EVA foam (Etilvinilacetato) - 3mm 60 40 1000
EVA foam (Etilvinilacetato) Black - 10mm 35 90 1000 90 15 1000 90 10 1000
EVA Foam (Ethylene-Vinyl Acetate) - Yellow - 11mm 20 100 1000 90 15 1000 90 10 1000
Paper - 3mm / 250gr 60 30 5000
Wood - Cherry/Alder/Walnut - 3mm 25 80 500 70 100
Wood - Cherry/Alder/Walnut - 6mm 10 100 500 70 100
Wood - Plywood (2mm) / Madera 15 40 500 70 100
Wood - Plywood (3mm) / Madera 10 85 2000 70 100
Wood - Plywood (4mm) / Madera 20 90 2500 70 10 500 100 10 500
Wood - Plywood (5mm) / Madera 15 90 2500 80 10 500 100 9 500
Wood - Plywood (0.5mm) / Madera 30 20 500 70 100
Wood - MDF (4mm) 20 90 500 70 10 500 100 20 500
Wood Veneer - 0.7mm 85 55 500 70 5 500 100 5 500
Felt (1mm) / Fieltro 80 25 250
Felt - Black (5mm) / Fieltro 55 55 250 100 5 250 100 10 250
Fabric - Thin 80 30 500
Foam with textile - 3mm 65 55 250 100 15 250 100 10 250
Lycra - White - 0.3mm 70 30 500 100 3 500 100 8 500
Paper - 0.3mm 50 50 500
Paper - White - 0.6mm 80 35 500 100 3 500 100 10 500
Paper - Black finish - 1.3 mm 75 40 500 90 5 500 90 10 500
Paper - Grey - 1.5mm 75 55 500 100 10 500 90 10 500
Paper - Parchment (for lamp making) 80 10 500
Cardboard - Corrugated (4mm/1 layers) 40 45 500 100 10 500 100 20 500
Cardboard - Corrugated (5mm/2 layers) 40 65 500 100 20 500 100 15 500
Cardboard - Corrugated high res. - white (6mm/1 layer) 2x 20 85 500 100 10 500 100 15 500

Note: Settings above are a good starting point. Laser cutting quality is affected by several factors including lens cleanliness, maintenance and/or aging laser tube. If you are not achieveing a cut, try to increase the power, decrease the speed or a do combination of both. Change settings with 5-10% step at a time.

Suppliers

For a supplier list take a look at this table maintained by de Fab Lab BARCELONA


Machine work flow

  • If you are not going to use the computer in the Fab Lab, install the Epilog drivers in your computer (you can reach the machine inside the Fab Lab network).
  • Turn on the main fume extractor in the big laser cutter switch panel.
  • Turn on the small air compressor on the left hand side of the machine.
  • Turn on the laser cutter (left side of the machine).
  • Make sure the material you want to use is in the 'Materials and configuration' list. If it is not there, ask the Fab Lab responsible.
  • Measure the size of your material board.
  • From your vector editing software, once you are ready for printing and if you already installed the driver, press Ctrl+P or select 'Print'.
  • Select 'Epilog Engraver' from the printer list and go to 'Printer settings' or 'Properties'.
  • The laser cutter driver interface should appear. Here you can set-up the laser's power and speed according to how the vector paths in your drawing are organized (you can also print raster images).
  • For a vector job:
    • In the 'General' tab, under 'Job type' select 'Vector'.
    • Set the size of the material sheet under 'Piece Size'.
    • Set to 'Vector sorting' and 'Optimize'.
    • In the 'Color mapping' tab select the check box 'Color mapping'. You should have organized your drawing in different colors if you need to do different types of jobs (for example engraving and cutting).
    • Once this is activated, you can set the power, the speed, and other parameters for every single color in your drawing. Take a look at the 'Materials and configuration' list above for the proper power/speed values according to the material you are using.
    • The list order determines the execution sequence of every type of job. You should allays engrave first and cut later. You can change the order by selecting a color and pressing the up and down arrows.
    • Once you are done with this configuration, press 'OK'.
  • For a raster job:
    • You should see the parts that you want to cut/engrave fitting the material in the preview. If not, you should scale, move, rotate or change the units of the drawing to get it as you want.
    • Finalize the process with 'Print' and the file will be sent to the laser cutter.
  • At the machine:
    • Open the hood and place the material on the metal bed without hitting the cutting head.
    • If the material you use is to thick (engraving bigger objects), you should lower the bed.
      • To lower the bed:
        • Press 'X/Y off' and bring the bed to the desired z position by pressing the 'up' and 'down' arrows.
    • Turn on the laser pointer 'Puntero'.
    • Set the machine head to the origin by pressing 'Restaur.' and focus the laser by pressing 'Enfocar' and 'GO/Entra'.
      • If you want to change the x/y origin follow this steps:
        • Press 'X/Y off' and bring the laser manually to the desire origin.
        • Then press 'Ajuste Inicio' and you should have now a new origin point.
  • If you already sent the job to the machine you will see 'Job:job name' in the display.
  • Pressing the up and down arrows will allow you to select the different jobs stored in the machine.
  • Press 'GO/Entra' to start cutting/engraving.
  • Press 'STOP/Salir' if something burns inside the machine or the material moves from its original position.
  • Don't leave the machine unattended.
the Epilog Legend 36 interface pannel
Epilog Legend 36 interface pannel

Important commands

Structure:

External links

Maintenance

Downloads