Epilog Laser Cutter 75

From Fab Lab Bcn WIKI
Revision as of 09:16, 9 May 2018 by Giacomo (Talk | contribs)

Jump to: navigation, search
Epilog Laser Cutter 75

Contents

Technical specifications

  • Cutting area 900 x 600 millimeters / 35.4" x 23.6" inches
  • Cutting power max. 75 Watt.
  • Maximum Power Consumption:

Health & Safety

CAM

  • 2D Printer driver from most CAD or ilustration software
  • From PDF

Tools

  • Tools here

Materials and configurations

Settings

Laser settings for common materials - Epilog 75W
Material Cut Engraving Raster Engraving - 600 DPI
Speed (%) Power (%) Frequency (Hz) Speed (%) Power (%) Frequency (Hz) Speed (%) Power (%) Frequency (Hz)
Polypropylene - White - 0.5mm 55 50 5000 100 10 5000 100 15 5000
Polypropylene - Transparent - 0.8mm 35 60 5000 100 20 5000 80 20 5000
Wood - Plywood - 4mm 20 90 300 70 10 500 100 10 500
Paper - Grey - 1.5mm 55 75 500 100 10 500 90 10 500
Wood - MDF - 5mm 15 100 300 70 10 500 100 20 500
Acrylic - Transparent - 2mm 30 90 5000 n/a n/a n/a n/a n/a n/a
Acrylic - TransparentMatt - 3mm 20 90 5000 n/a n/a n/a 100 15 5000

Note: Settings above are a good starting point. Laser cutting quality is affected by several factors including lens cleanliness, maintenance and/or aging laser tube. If you are not achieveing a cut, try to increase the power, decrease the speed or a do combination of both. Change settings with 5-10% step at a time.

Suppliers

For a supplier list take a look at this table maintained by de Fab Lab BARCELONA

Machine work flow

  • If you are not going to use the computer in the Fab Lab, Harga AC Murahinstall the Epilog drivers in your computer (you can reach the machine inside the Fab Lab network).
  • Turn on the main fume extractor in the big laser cutter switch panel.
  • Turn on the small air compressor on the left hand side of the machine.
  • Turn on the laser cutter (left side of the machine).
  • Make sure the material Harga Ban Motor Corsa you want to use is in the 'Materials and configuration' list. If it is not there, ask the Fab Lab responsible.
  • Measure the size of your material board.
  • From your vector editing software, once you are ready for printing and if you already installed the driver, press Ctrl+P or select 'Print'.
  • Select 'Epilog Engraver' from the printer list and go to 'Printer settings' or 'Properties'.
  • The laser cutter driver interface should appear. Here you can set-up the laser's power and speed according to how the vector paths in your drawing are organized (you can also print raster images). Harga HP Samsung
  • For a vector job:
    • In the 'General' tab, under 'Job type' select 'Vector'.
    • Set the size of the material sheet under 'Piece Size'.
    • Set to 'Vector sorting' and 'Optimize'.
    • In the 'Color mapping' tab select the check box 'Color mapping'. You should have organized your drawing in different colors if you need to do different types of jobs (for example engraving and cutting).
    • Once this is activated, you can set the power, the speed, and other parameters for every single color in your drawing. Take a look at the 'Materials and configuration' list above for the proper power/speed values according to the material you are using.
    • The list order determines the execution sequence of every type of job. You should allays engrave first and cut later. You can change the order by selecting a color and pressing the up and down arrows.
    • Once you are done with this configuration, press 'OK'.
  • For a raster job:
    • You should see the parts that you want to cut/engrave fitting the material in the preview. If not, you should scale, move, rotate or change the units of the drawing to get it as you want.
    • Finalize the process with 'Print' and the file will be sent to the laser cutter.
  • At the machine:
    • Open the hood and place the material on the metal bed without hitting the cutting head.
    • If the material you use is to thick (engraving bigger objects), you should lower the bed.
      • To lower the bed:
        • Press 'X/Y off' and bring the bed to the desired z position by pressing the 'up' and 'down' arrows.
    • Turn on the laser pointer 'Puntero'.
    • Set the machine head to the origin by pressing 'Restaur.' and focus the laser by pressing 'Enfocar' and 'GO/Entra'.
      • If you want to change the x/y origin follow this steps:
        • Press 'X/Y off' and bring the laser manually to the desire origin.
        • Then press 'Ajuste Inicio' and you should have now a new origin point.
  • If you already sent the job to the machine you will see 'Job:job name' in the display.
  • Pressing the up and down arrows will allow you to select the different jobs stored in the machine.
  • Press 'GO/Entra' to start cutting/engraving.
  • Press 'STOP/Salir' if something burns inside the machine or the material moves from its original position.
  • Don't leave the machine unattended.
the Epilog Legend 36 interface pannel
Epilog Legend 36 interface pannel

Important commands

Structure:

External links

Maintenance

Downloads

Epilog Laser Cutter

Technical specifications

  • Cutting area 900 x 600 millimeters / 35.4" x 23.6" inches
  • Cutting power max. 75 Watt.
  • Maximum Power Consumption:

Health & Safety

CAM

  • 2D Printer driver from most CAD or ilustration software
  • From PDF

Tools

  • Tools here

Materials and configurations

Suppliers

For a supplier list take a look at this table maintained by de Fab Lab BARCELONA

Polypropylene (0.5mm) / Polipropileno

CUT:

  • Speed: 60%
  • Power: 60%

ENGRAVE:

  • Speed: 85%
  • Power: 20%

Polypropylene (1.2mm) / Polipropileno

CUT:

  • Speed: 15%
  • Power: 90%

ENGRAVE:

  • Speed: 60%
  • Power: 40%

Polypropylene (0.8mm) / Polipropileno

CUT:

  • Speed: 60%
  • Power: 70%

Poly(methyl methacrylate)(3mm) / Plexiglass

CUT:

  • Speed: 15%
  • Power: 60%

ENGRAVE:

  • Speed: 65%
  • Power: 10%

Poly(methyl methacrylate)(1mm) / Plexiglass

CUT:

  • Speed: 60%
  • Power: 70%

ENGRAVE:

  • Speed: 90%
  • Power: 15%

Poly(methyl methacrylate) (5mm) / Plexiglass

CUT:

  • Speed: 10% / 15%
  • Power: 90% / 80%

ENGRAVE:

  • Speed: 65%
  • Power: 10%

Etilvinilacetato (3mm) / Foami - Eva

CUT:

  • Speed: 40%
  • Power: 60%

Paper(250gr/3mm) / Papel

CUT:

  • Speed: 60%
  • Power: 30%

ENGRAVE:

  • Speed: 85%
  • Power: 6%

Paper (0.3mm) / Papel

CUT:

  • Speed: 50%
  • Power: 50%

ENGRAVE:

  • Speed: 95%
  • Power: 3%

Paper(shine 1 side) / Papel

CUT:

  • Speed: 60%
  • Power: 25%

ENGRAVE:

  • Speed: 95%
  • Power: 4%

Parchment Paper(for lamp making) / Papel Pergamino (para hacer lamparas)

CUT:

  • Speed: 85%
  • Power: 10%

Transparent Paper / Papel transparente

CUT:

  • Speed: 75%
  • Power: 20%

Cardboard Corrugated (5mm/2 layers) / Carton Corrugado

CUT:

  • Speed: 55%
  • Power: 45%

ENGRAVE:

  • Speed: 90%
  • Power: 10%

Generic Cardboard / Cartulina común

CUT:

  • Speed: 100%
  • Power: 15%

ENGRAVE:

  • Speed: 100%
  • Power: 4%

Stone Cardboard (3mm) / Carton Piedra

CUT:

  • Speed: 20%
  • Power: 50%

Plywood (0.6mm) (Rolling roll)/ Madera (Laminada rollo)

CUT:

  • Speed: 40%
  • Power: 10%

ENGRAVE:

  • Speed: 95%
  • Power: 4%


Plywood (0.6mm) (Plywood)/ Madera (contrachapado Abedul)

CUT:

  • Speed: 50%
  • Power: 50%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (2mm) / Madera

CUT:

  • Speed: 15%
  • Power: 40%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (3mm) / Madera

CUT:

  • Speed: 15%
  • Power: 45%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

MDF (3mm) / Madera DM

CUT:

  • Speed: 15%
  • Power: 65%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (5mm) / Madera

CUT:

  • Speed: 15%
  • Power: 85%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (0.5mm deep)/ Madera RASTER SOLID

ENGRAVE:

  • Speed: 30%
  • Power: 20%

Felt (3mm) / Fieltro

CUT:

  • Speed: 60%-70%
  • Power: 110%

Felt (1mm) / Fieltro

CUT:

  • Speed: 90% (70%)
  • Power: 10%

Grabar sobre piedra/ Raster Image on stone

ENGRAVE:

  • Speed: 90%
  • Power: 20%

Thin Fabric

CUT:

  • Speed: 80%
  • Power: 30%

Machine work flow

  • If you are not going to use the computer in the Fab Lab, Harga AC Murahinstall the Epilog drivers in your computer (you can reach the machine inside the Fab Lab network).
  • Turn on the main fume extractor in the big laser cutter switch panel.
  • Turn on the small air compressor on the left hand side of the machine.
  • Turn on the laser cutter (left side of the machine).
  • Make sure the material Harga Ban Motor Corsa you want to use is in the 'Materials and configuration' list. If it is not there, ask the Fab Lab responsible.
  • Measure the size of your material board.
  • From your vector editing software, once you are ready for printing and if you already installed the driver, press Ctrl+P or select 'Print'.
  • Select 'Epilog Engraver' from the printer list and go to 'Printer settings' or 'Properties'.
  • The laser cutter driver interface should appear. Here you can set-up the laser's power and speed according to how the vector paths in your drawing are organized (you can also print raster images). Harga HP Samsung
  • For a vector job:
    • In the 'General' tab, under 'Job type' select 'Vector'.
    • Set the size of the material sheet under 'Piece Size'.
    • Set to 'Vector sorting' and 'Optimize'.
    • In the 'Color mapping' tab select the check box 'Color mapping'. You should have organized your drawing in different colors if you need to do different types of jobs (for example engraving and cutting).
    • Once this is activated, you can set the power, the speed, and other parameters for every single color in your drawing. Take a look at the 'Materials and configuration' list above for the proper power/speed values according to the material you are using.
    • The list order determines the execution sequence of every type of job. You should allays engrave first and cut later. You can change the order by selecting a color and pressing the up and down arrows.
    • Once you are done with this configuration, press 'OK'.
  • For a raster job:
    • You should see the parts that you want to cut/engrave fitting the material in the preview. If not, you should scale, move, rotate or change the units of the drawing to get it as you want.
    • Finalize the process with 'Print' and the file will be sent to the laser cutter.
  • At the machine:
    • Open the hood and place the material on the metal bed without hitting the cutting head.
    • If the material you use is to thick (engraving bigger objects), you should lower the bed.
      • To lower the bed:
        • Press 'X/Y off' and bring the bed to the desired z position by pressing the 'up' and 'down' arrows.
    • Turn on the laser pointer 'Puntero'.
    • Set the machine head to the origin by pressing 'Restaur.' and focus the laser by pressing 'Enfocar' and 'GO/Entra'.
      • If you want to change the x/y origin follow this steps:
        • Press 'X/Y off' and bring the laser manually to the desire origin.
        • Then press 'Ajuste Inicio' and you should have now a new origin point.
  • If you already sent the job to the machine you will see 'Job:job name' in the display.
  • Pressing the up and down arrows will allow you to select the different jobs stored in the machine.
  • Press 'GO/Entra' to start cutting/engraving.
  • Press 'STOP/Salir' if something burns inside the machine or the material moves from its original position.
  • Don't leave the machine unattended.
the Epilog Legend 36 interface pannel
Epilog Legend 36 interface pannel

Important commands

Structure:

External links

Maintenance

Downloads

Epilog Laser Cutter

Technical specifications

  • Cutting area 900 x 600 millimeters / 35.4" x 23.6" inches
  • Cutting power max. 75 Watt.
  • Maximum Power Consumption:

Health & Safety

CAM

  • 2D Printer driver from most CAD or ilustration software
  • From PDF

Tools

  • Tools here

Materials and configurations

Suppliers

For a supplier list take a look at this table maintained by de Fab Lab BARCELONA

Polypropylene (0.5mm) / Polipropileno

CUT:

  • Speed: 60%
  • Power: 60%

ENGRAVE:

  • Speed: 85%
  • Power: 20%

Polypropylene (1.2mm) / Polipropileno

CUT:

  • Speed: 15%
  • Power: 90%

ENGRAVE:

  • Speed: 60%
  • Power: 40%

Polypropylene (0.8mm) / Polipropileno

CUT:

  • Speed: 60%
  • Power: 70%

Poly(methyl methacrylate)(3mm) / Plexiglass

CUT:

  • Speed: 15%
  • Power: 60%

ENGRAVE:

  • Speed: 65%
  • Power: 10%

Poly(methyl methacrylate)(1mm) / Plexiglass

CUT:

  • Speed: 60%
  • Power: 70%

ENGRAVE:

  • Speed: 90%
  • Power: 15%

Poly(methyl methacrylate) (5mm) / Plexiglass

CUT:

  • Speed: 10% / 15%
  • Power: 90% / 80%

ENGRAVE:

  • Speed: 65%
  • Power: 10%

Etilvinilacetato (3mm) / Foami - Eva

CUT:

  • Speed: 40%
  • Power: 60%

Paper(250gr/3mm) / Papel

CUT:

  • Speed: 60%
  • Power: 30%

ENGRAVE:

  • Speed: 85%
  • Power: 6%

Paper (0.3mm) / Papel

CUT:

  • Speed: 50%
  • Power: 50%

ENGRAVE:

  • Speed: 95%
  • Power: 3%

Paper(shine 1 side) / Papel

CUT:

  • Speed: 60%
  • Power: 25%

ENGRAVE:

  • Speed: 95%
  • Power: 4%

Parchment Paper(for lamp making) / Papel Pergamino (para hacer lamparas)

CUT:

  • Speed: 85%
  • Power: 10%

Transparent Paper / Papel transparente

CUT:

  • Speed: 75%
  • Power: 20%

Cardboard Corrugated (5mm/2 layers) / Carton Corrugado

CUT:

  • Speed: 55%
  • Power: 45%

ENGRAVE:

  • Speed: 90%
  • Power: 10%

Generic Cardboard / Cartulina común

CUT:

  • Speed: 100%
  • Power: 15%

ENGRAVE:

  • Speed: 100%
  • Power: 4%

Stone Cardboard (3mm) / Carton Piedra

CUT:

  • Speed: 20%
  • Power: 50%

Plywood (0.6mm) (Rolling roll)/ Madera (Laminada rollo)

CUT:

  • Speed: 40%
  • Power: 10%

ENGRAVE:

  • Speed: 95%
  • Power: 4%


Plywood (0.6mm) (Plywood)/ Madera (contrachapado Abedul)

CUT:

  • Speed: 50%
  • Power: 50%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (2mm) / Madera

CUT:

  • Speed: 15%
  • Power: 40%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (3mm) / Madera

CUT:

  • Speed: 15%
  • Power: 45%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

MDF (3mm) / Madera DM

CUT:

  • Speed: 15%
  • Power: 65%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (5mm) / Madera

CUT:

  • Speed: 15%
  • Power: 85%

ENGRAVE:

  • Speed: 40%
  • Power: 10%

Plywood (0.5mm deep)/ Madera RASTER SOLID

ENGRAVE:

  • Speed: 30%
  • Power: 20%

Felt (3mm) / Fieltro

CUT:

  • Speed: 60%-70%
  • Power: 110%

Felt (1mm) / Fieltro

CUT:

  • Speed: 90% (70%)
  • Power: 10%

Grabar sobre piedra/ Raster Image on stone

ENGRAVE:

  • Speed: 90%
  • Power: 20%

Thin Fabric

CUT:

  • Speed: 80%
  • Power: 30%

Machine work flow

  • If you are not going to use the computer in the Fab Lab, Harga AC Murahinstall the Epilog drivers in your computer (you can reach the machine inside the Fab Lab network).
  • Turn on the main fume extractor in the big laser cutter switch panel.
  • Turn on the small air compressor on the left hand side of the machine.
  • Turn on the laser cutter (left side of the machine).
  • Make sure the material Harga Ban Motor Corsa you want to use is in the 'Materials and configuration' list. If it is not there, ask the Fab Lab responsible.
  • Measure the size of your material board.
  • From your vector editing software, once you are ready for printing and if you already installed the driver, press Ctrl+P or select 'Print'.
  • Select 'Epilog Engraver' from the printer list and go to 'Printer settings' or 'Properties'.
  • The laser cutter driver interface should appear. Here you can set-up the laser's power and speed according to how the vector paths in your drawing are organized (you can also print raster images). Harga HP Samsung
  • For a vector job:
    • In the 'General' tab, under 'Job type' select 'Vector'.
    • Set the size of the material sheet under 'Piece Size'.
    • Set to 'Vector sorting' and 'Optimize'.
    • In the 'Color mapping' tab select the check box 'Color mapping'. You should have organized your drawing in different colors if you need to do different types of jobs (for example engraving and cutting).
    • Once this is activated, you can set the power, the speed, and other parameters for every single color in your drawing. Take a look at the 'Materials and configuration' list above for the proper power/speed values according to the material you are using.
    • The list order determines the execution sequence of every type of job. You should allays engrave first and cut later. You can change the order by selecting a color and pressing the up and down arrows.
    • Once you are done with this configuration, press 'OK'.
  • For a raster job:
    • You should see the parts that you want to cut/engrave fitting the material in the preview. If not, you should scale, move, rotate or change the units of the drawing to get it as you want.
    • Finalize the process with 'Print' and the file will be sent to the laser cutter.
  • At the machine:
    • Open the hood and place the material on the metal bed without hitting the cutting head.
    • If the material you use is to thick (engraving bigger objects), you should lower the bed.
      • To lower the bed:
        • Press 'X/Y off' and bring the bed to the desired z position by pressing the 'up' and 'down' arrows.
    • Turn on the laser pointer 'Puntero'.
    • Set the machine head to the origin by pressing 'Restaur.' and focus the laser by pressing 'Enfocar' and 'GO/Entra'.
      • If you want to change the x/y origin follow this steps:
        • Press 'X/Y off' and bring the laser manually to the desire origin.
        • Then press 'Ajuste Inicio' and you should have now a new origin point.
  • If you already sent the job to the machine you will see 'Job:job name' in the display.
  • Pressing the up and down arrows will allow you to select the different jobs stored in the machine.
  • Press 'GO/Entra' to start cutting/engraving.
  • Press 'STOP/Salir' if something burns inside the machine or the material moves from its original position.
  • Don't leave the machine unattended.
the Epilog Legend 36 interface pannel
Epilog Legend 36 interface pannel

Important commands

Structure:

External links

Maintenance

Downloads