Difference between revisions of "Multicam Laser Cutter"

From Fab Lab Bcn WIKI
Jump to: navigation, search
m
(WHealth & Safety)
 
(48 intermediate revisions by 8 users not shown)
Line 1: Line 1:
 
[[Category:machines]]
 
[[Category:machines]]
 +
 +
[[File:Machines 1.jpg| frame |Multicam 2000 Laser Cutter]]
  
 
==Technical specifications==
 
==Technical specifications==
Line 12: Line 14:
 
*Y axis stroke 60” (1524 mm) and 80” (2032 mm)
 
*Y axis stroke 60” (1524 mm) and 80” (2032 mm)
 
*X axis stroke 50” (1270 mm), 100” (2540 mm), 120” (3048 mm),144” (3658 mm), 168” (4267 mm), and 240” (6096 mm)
 
*X axis stroke 50” (1270 mm), 100” (2540 mm), 120” (3048 mm),144” (3658 mm), 168” (4267 mm), and 240” (6096 mm)
 +
 +
==Health & Safety==
 +
* Do not use materials that are not suitable for laser cutting! Ask the FabLab operators if you're not sure about your material.
 +
* Do not stand on the side of the machine! Only in the front. The machine can move suddenly and quickly and can hit you.
 +
* Do not continue cutting if something is going wrong! For example: if there is flame or a lot of smoke or it's not cutting or the material is melting. Pause the machine and call a FabLab operator.
 +
* Do not change the material on the remote! It has to be "cardboard" always.
  
 
==Materials and configuration==
 
==Materials and configuration==
Line 18: Line 26:
 
*Plywood is a manufactured wood panel made from thin sheets of wood veneer. It is one of the most widely used wood products. It is flexible, inexpensive, workable, re-usable, and can usually be locally manufactured.
 
*Plywood is a manufactured wood panel made from thin sheets of wood veneer. It is one of the most widely used wood products. It is flexible, inexpensive, workable, re-usable, and can usually be locally manufactured.
 
*Medium-density fibreboard (MDF) is an engineered wood product formed by breaking down hardwood or softwood residuals into wood fibres, often in a defibrator, combining it with wax and a resin binder, and forming panels by applying high temperature and pressure. MDF is denser than plywood.
 
*Medium-density fibreboard (MDF) is an engineered wood product formed by breaking down hardwood or softwood residuals into wood fibres, often in a defibrator, combining it with wax and a resin binder, and forming panels by applying high temperature and pressure. MDF is denser than plywood.
[http://www.optimaweb.co.id/jasa-seo Jasa seo], [http://kiosauto.com Aksesoris mobil], [http://www.awanirentcar.com Sewa mobil jakarta]
 
  
===0.5mm===
+
 
 +
====0.5mm====
 
CUT  
 
CUT  
 
*Speed: 100
 
*Speed: 100
Line 28: Line 36:
 
*Power:  15
 
*Power:  15
  
===3mm===  
+
====3mm====  
 
CUT  
 
CUT  
 
*Speed:  30
 
*Speed:  30
Line 36: Line 44:
 
*Power:  60
 
*Power:  60
  
===4mm Plywood===
+
==='''Plywood:'''===
 +
 
 +
====4mm====
 
CUT  
 
CUT  
 
*Speed:  40
 
*Speed:  40
 
*Power: 180
 
*Power: 180
  
===4mm MDF===
+
==='''Bent Plywood:'''===
 +
 
 +
====5mm====
 +
CUT
 +
*Speed:  90
 +
*Power: 130
 +
 
 +
ENGRAVE
 +
*Speed:  110
 +
*Power: 40
 +
 
 +
==='''MDF'''===
 +
====4mm====
 
CUT
 
CUT
*Speed:  40
+
*Speed:  30
*Power: 180
+
*Power: 185
 +
ENGRAVE
 +
*Speed:
 +
*Power:
 +
====4mm====
 +
CUT
 +
*Speed:  35
 +
*Power: 150
 
ENGRAVE
 
ENGRAVE
 
*Speed: 60
 
*Speed: 60
 
*Power: 50
 
*Power: 50
  
===5mm===
+
====5mm====
 
CUT  
 
CUT  
*Speed: 22
+
*Speed: 20
*Power: 220
+
*Power: 185
 
ENGRAVE
 
ENGRAVE
 
*Speed: 60
 
*Speed: 60
 
*Power: 50
 
*Power: 50
  
===6mm===
+
====6mm====
 
CUT  
 
CUT  
 
*Speed: 20
 
*Speed: 20
Line 65: Line 94:
 
*Power: 60
 
*Power: 60
  
===7mm===
+
====7mm====
 
CUT  
 
CUT  
*Speed: 30
+
*Speed: 15
*Power: 240
+
*Power: 260
 
ENGRAVE
 
ENGRAVE
 
*Speed: 60
 
*Speed: 60
 
*Power: 60
 
*Power: 60
  
===10mm===
+
====10mm====
 
CUT  
 
CUT  
*Speed: 15
+
*Speed:13
*Power: 220
+
*Power: 330-340
 
ENGRAVE
 
ENGRAVE
 
*Speed: 60
 
*Speed: 60
Line 84: Line 113:
 
*Power:  80
 
*Power:  80
  
===12mm===
+
====12mm====
 
CUT  
 
CUT  
 
*Speed:  15
 
*Speed:  15
Line 92: Line 121:
 
*Power: 60
 
*Power: 60
  
===12mm===
+
====12mm====
 
CUT  
 
CUT  
 
*Speed:  15
 
*Speed:  15
Line 100: Line 129:
 
*Power: 60
 
*Power: 60
  
===13mm===
+
====13mm====
 
CUT  
 
CUT  
 
*Speed:  10
 
*Speed:  10
 
*Power: 370
 
*Power: 370
  
===15mm===
+
====15mm====
 
CUT  
 
CUT  
*Speed: 12
+
*Speed: 5
*Power: 380
+
*Power: 375
 
ENGRAVE
 
ENGRAVE
 
*Speed: 50
 
*Speed: 50
 
*Power: 70
 
*Power: 70
  
===20mm===
+
IN HIGH DENSITY WOOD SUCH AS MDF THE MAXIMUM THICKNESS IS 15 mm
 +
 
 +
==='''Poplar Plywood / Contraplacat Pollancre'''===
 +
 
 +
====4mm====
 
CUT  
 
CUT  
*Speed:  10
+
*Speed:  35
*Power: 380
+
*Power: 150
 +
ENGRAVE
 +
*Speed:  90
 +
*Power:  30
  
=== Contraplacat Pollancre 10mm===
+
====5mm====
 
CUT  
 
CUT  
*Speed:  40
+
*Speed:  20
*Power: 180
+
*Power: 185
 +
ENGRAVE
 +
*Speed: 
 +
*Power: 
 +
====10mm====
 +
CUT
 +
*Speed:  20
 +
*Power: 375
 
ENGRAVE
 
ENGRAVE
 
*Speed:  90
 
*Speed:  90
 
*Power:  30
 
*Power:  30
  
=== Contraplacat Pollancre 25mm===
+
====15mm====
 +
CUT
 +
*Speed:  5
 +
*Power: 375
 +
ENGRAVE
 +
*Speed: 
 +
*Power: 
 +
 
 +
====25mm====
 
CUT  
 
CUT  
 
*Speed:  22
 
*Speed:  22
Line 137: Line 188:
 
*Power: 150
 
*Power: 150
  
===='''Cardboard:'''====
+
==='''Cardboard:'''===
 
*Cardboard is a generic term for a heavy-duty paper of various strengths, ranging from a simple arrangement of a single thick sheet of paper to complex configurations featuring multiple corrugated and uncorrugated layers.
 
*Cardboard is a generic term for a heavy-duty paper of various strengths, ranging from a simple arrangement of a single thick sheet of paper to complex configurations featuring multiple corrugated and uncorrugated layers.
  
===1mm===
+
====1mm====
 
CUT  
 
CUT  
 
*Speed: 100
 
*Speed: 100
 
*Power:  80
 
*Power:  80
  
===1.5mm Grey===
+
====1.5mm Grey====
 
CUT
 
CUT
 
*Speed:  70
 
*Speed:  70
 
*Power: 100
 
*Power: 100
  
===2mm Grey===
+
====2mm Grey====
 
CUT  
 
CUT  
*Speed: 100
+
*Speed: 110
*Power: 120
+
*Power: 115
 
ENGRAVE
 
ENGRAVE
 
*Speed: 100
 
*Speed: 100
 
*Power:  80
 
*Power:  80
  
===3mm Grey===
+
====3mm Grey====
 
CUT  
 
CUT  
 
*Speed:  50
 
*Speed:  50
Line 166: Line 217:
 
*Power:  35
 
*Power:  35
  
===1mm Black===
+
====1mm Black====
 
CUT
 
CUT
 
*Speed:  90
 
*Speed:  90
 
*Power:  90
 
*Power:  90
  
===4mm Rippled===
+
====4mm Rippled====
 
CUT
 
CUT
 
*Speed: 100
 
*Speed: 100
Line 179: Line 230:
 
*Power:  65
 
*Power:  65
  
===6mm Rippled===
+
====6mm Rippled====
 
CUT
 
CUT
 
*Speed: 100
 
*Speed: 100
 
*Power: 160
 
*Power: 160
  
===Acuarela===
+
====Acuarela====
 
CUT
 
CUT
 
*Speed: 100
 
*Speed: 100
Line 192: Line 243:
 
*Power:  48
 
*Power:  48
  
===Cartulins Común / Generic Cardboard===
+
====Cartulins Común / Generic Cardboard====
 
CUT
 
CUT
 
*Speed: 120
 
*Speed: 120
Line 200: Line 251:
 
*Power:  46
 
*Power:  46
  
===='''Metacrilato/Methacrylate:'''====
+
==='''Metacrilato/Methacrylate:'''===
 
*Poly(methyl methacrylate) (PMMA) is a transparent thermoplastic, often used as a light or shatter-resistant alternative to glass. It is sometimes called acrylic glass. Chemically, it is the synthetic polymer of methyl methacrylate.
 
*Poly(methyl methacrylate) (PMMA) is a transparent thermoplastic, often used as a light or shatter-resistant alternative to glass. It is sometimes called acrylic glass. Chemically, it is the synthetic polymer of methyl methacrylate.
  
===2mm===
+
====2mm====
 
CUT
 
CUT
*Speed:  30
+
*Speed:  12
*Power:  90
+
*Power:  290
  
===3mm===
+
====3mm====
 
CUT
 
CUT
 
*Speed: 20
 
*Speed: 20
 
*Power: 90
 
*Power: 90
  
===3mm Verde Opal===
+
====3mm Verde Opal====
 
CUT
 
CUT
 
*Speed:  45
 
*Speed:  45
 
*Power: 112
 
*Power: 112
  
===4mm===
+
====4mm====
 
CUT
 
CUT
 
*Speed: 10
 
*Speed: 10
Line 226: Line 277:
 
*Power: 80
 
*Power: 80
  
===5mm===
+
====5mm====
 
CUT
 
CUT
 
*Speed: 15
 
*Speed: 15
 
*Power: 100
 
*Power: 100
  
===5mm Blanco Opal===
+
====5mm Blanco Opal====
 
CUT
 
CUT
 
*Speed:  33
 
*Speed:  33
 
*Power: 200
 
*Power: 200
  
===6mm===
+
====6mm====
 
CUT
 
CUT
 
*Speed:  40
 
*Speed:  40
 
*Power: 200
 
*Power: 200
  
===8mm===
+
====8mm====
 
CUT
 
CUT
 
*Speed:  15
 
*Speed:  15
Line 249: Line 300:
 
*Power: 160
 
*Power: 160
  
===10mm===
+
====10mm====
 
CUT
 
CUT
 
*Speed:  10
 
*Speed:  10
Line 257: Line 308:
 
*Power:  40
 
*Power:  40
  
===='''Polypropylene:'''====
+
==='''Polypropylene:'''===
 
*Polypropylene (PP), also known as polypropene, is a thermoplastic polymer used in a wide variety of applications including packaging, textiles (e.g., ropes, thermal underwear and carpets), stationery, plastic parts and reusable containers of various types, laboratory equipment, loudspeakers, automotive components, and polymer banknotes.
 
*Polypropylene (PP), also known as polypropene, is a thermoplastic polymer used in a wide variety of applications including packaging, textiles (e.g., ropes, thermal underwear and carpets), stationery, plastic parts and reusable containers of various types, laboratory equipment, loudspeakers, automotive components, and polymer banknotes.
  
===0.5mm===
+
====0.5mm====
 
CUT
 
CUT
 
*Speed:  90
 
*Speed:  90
Line 268: Line 319:
 
*Power:  60
 
*Power:  60
  
===0.8mm===
+
====0.8mm====
 
CUT
 
CUT
 
*Speed:  90
 
*Speed:  90
Line 276: Line 327:
 
*Power:  40
 
*Power:  40
  
===1.5mm===
+
====1.5mm====
 
CUT
 
CUT
 
*Speed:  70
 
*Speed:  70
Line 284: Line 335:
 
*Power:  90
 
*Power:  90
  
===='''Fabrics'''====
+
==='''Fabrics'''===
  
===Cotton fabric===
+
====Cotton====
 
CUT
 
CUT
 
*Speed:  90
 
*Speed:  90
Line 294: Line 345:
 
*Power:  40
 
*Power:  40
  
===Suede===
+
====Suede====
 
RASTER
 
RASTER
 
*Speed:  600
 
*Speed:  600
 
*Power:  32
 
*Power:  32
  
===Felt/Fieltro===
+
====Felt/Fieltro====
 
CUT
 
CUT
*Speed:  50
+
*Speed:  60-70
*Power:  180
+
*Power:  110
  
===='''Other:'''====
+
==='''Other:'''===
  
===Plastico dos capas con aire 4mm Plastic 2 layers with air===
+
====Plastico dos capas con aire 4mm / Plastic 2 layers with air====
 
CUT
 
CUT
 
*Speed:  90
 
*Speed:  90
 
*Power: 200
 
*Power: 200
  
===Acrylic 3mm===
+
====Acrylic 3mm====
 
CUT
 
CUT
 
*Speed:  40
 
*Speed:  40
 
*Power: 170
 
*Power: 170
  
===Plastic sheets welding===
+
====Plastic sheets welding====
 
ENGRAVE
 
ENGRAVE
 
*Cut pressure 6
 
*Cut pressure 6
Line 326: Line 377:
 
==How to prepare and send files==
 
==How to prepare and send files==
 
* 1. Open EnRoute. If it's already open – go straight to step 2
 
* 1. Open EnRoute. If it's already open – go straight to step 2
* 2. Open a new file and set your sheet size (in mm)
+
* 2. Open a new file ( File - New ) and set your sheet size (width/heigh in mm, thickness is not important)
* 3. Import your .dxf file: File – Import – find your file  
+
* 3. Import your .dxf file: File – Import – find your file
 
* 4. Make sure that your drawing is inside the red border. If you need to scale or move your drawing: select everything and press F2 on the keyboard
 
* 4. Make sure that your drawing is inside the red border. If you need to scale or move your drawing: select everything and press F2 on the keyboard
 
* 5. Select everything and go to Transform – Merge selection… and click OK  
 
* 5. Select everything and go to Transform – Merge selection… and click OK  
* 6. If you are using two strategies (engraving and cutting) then go to Layers and turn the engraving layer ON and the cutting layer OFF
+
* 6. If you are using two strategies (engraving and cutting) [http://www.tabloidharga.com/tablet-murah harga tablet terbaru] then go to Layers ( Setup - Layers ) and turn the engraving layer ON and the cutting layer OFF
* 7. Click on the 'Engrave' button, in the drop-down menu select your Strategy – 'engrave' and click OK. You will see the generated paths for your design
+
* 7. Select all and click on the 'Engraving...' button (Toolpath - Engraving), in the drop-down menu select your Strategy – 'eng' and click OK. You will see the generated paths for your design
 
* 8. Go to Layers again and switch your cutting layer ON and the engraving one OFF
 
* 8. Go to Layers again and switch your cutting layer ON and the engraving one OFF
* 9. Go to Engrave again but this time choose 'cut' in the drop-down menu
+
* 9. Select all and go to Engraving again but this time choose 'cut' in the drop-down menu
 
* 10. Switch all the layers ON. You will see all your paths together
 
* 10. Switch all the layers ON. You will see all your paths together
* 11. Click the 'Output option' icon. Go to the 'Tool Order' section and make sure that 'engrave' is the first. If not – drag it up. If you have smaller pieces inside bigger pieces (holes, openings, etc.) then in 'Object Order' check 'Inside out'. Also check 'Small parts first'. Press 'To File'
+
* 11. Click the 'Output option' ( Machining - Output ) icon. Go to the 'Tool Order' section and make sure that 'engrave' is the first. If not – drag it up (click on the left box next to the number when the cursor will be an arrow to drag it up). If you have smaller pieces inside bigger pieces (holes, openings, etc.) then in 'Object Order' check 'Inside out'. Also check 'Small parts first'. Press 'To File'
 
* 12. Save your file inside 'Dnc files' folder. Use one of the existing folders (MAA, FabAcademy, etc.). You can also create your own folder
 
* 12. Save your file inside 'Dnc files' folder. Use one of the existing folders (MAA, FabAcademy, etc.). You can also create your own folder
 
* 13. Done! Your file is sent to the machine
 
* 13. Done! Your file is sent to the machine
 +
 +
<gallery widths=400 heights=400 mode=packed style="text-align:center">
 +
File:image.png|1
 +
File:Image (laser1).png|2
 +
File:Image (laser3).png|3
 +
File:Image (laser4).png|5
 +
File:Image (laser5).png|6
 +
File:Image laser(6).png|7
 +
File:Image laser(7).png|8
 +
File:Image laser(8).png|9
 +
File:Image laser(9).png|10
 +
File:Image laser(10).png|11
 +
</gallery>
  
 
===Notes===
 
===Notes===
Line 350: Line 414:
 
**Your file has to be flat (on 0 in Z axis).
 
**Your file has to be flat (on 0 in Z axis).
 
**Your home is in the lower left edge of your sheet and has to be in 0, 0, 0.
 
**Your home is in the lower left edge of your sheet and has to be in 0, 0, 0.
**If you have an AutoCAD file do not double-click it, right-click it instead and select "Open with – AutoCAD'.
 
  
 
==How to turn on the machine==
 
==How to turn on the machine==
Line 357: Line 420:
 
**Turn Laser to 'ON'
 
**Turn Laser to 'ON'
 
**Turn Shutter to 'OPEN'
 
**Turn Shutter to 'OPEN'
**Turn Mode to 'MAINT'
+
**Turn Mode to 'RUN'
 
**Fume collector to 'ON'
 
**Fume collector to 'ON'
**All the light should be on except for RUN MODE
+
**All the light should be on  
 +
 
 +
 
 +
 
 +
 
 +
 
 
*On the wall:
 
*On the wall:
 
**Turn on the main compressor (there's a small box on the wall with two blue caps and two red caps: the switches inside this box have to be up)
 
**Turn on the main compressor (there's a small box on the wall with two blue caps and two red caps: the switches inside this box have to be up)
 +
*On the machine:
 +
**Turn on the internal Ventilator(There's a small switch on the far rear of the machine)
 
*On the remote:
 
*On the remote:
 
**SHIFT + HOME to home the machine (SHIFT is button № 20 and HOME is button № 1)
 
**SHIFT + HOME to home the machine (SHIFT is button № 20 and HOME is button № 1)
  
[[File:Multicam_buttons_md.png|frame|none|alt=the Multicam 2000 interface pannel|Multicam 2000 interface pannel]]
+
 
 +
<gallery widths=400 heights=400 mode=packed style="text-align:center">
 +
File:Multicam_buttons_md.png|Multicam 2000 interface pannel
 +
File:IMG 20160419 133302.jpg| Control panel
 +
File:IMG 20160419 133349.jpg| On the wall
 +
File:IMG 20160419 133404.jpg| On the machine
 +
</gallery>
  
 
==How to cut==
 
==How to cut==
 
* 1. Place your material on the bed of the machine. The X axis is the longer part of the laser cutter and the Y axis is the sorted one. Home (0,0,0) is on the lower left corner.
 
* 1. Place your material on the bed of the machine. The X axis is the longer part of the laser cutter and the Y axis is the sorted one. Home (0,0,0) is on the lower left corner.
* 2. Set material thickness and surface height. Press SET SURFACE (button № 6) and ENTER (button № 30) and set the thickness of your material. The values are in millimeters. Press ENTER again, then button 0 and hold it until the sensor touches the surface to automatically set the height.
+
* 2. Set material thickness and surface height. Press SET SURFACE (button № 6) and ENTER (button № 30) and set the thickness of your material. The values are in millimeters [http://www.tabloidharga.com/sepeda-gunung sepeda gunung murah]. Press ENTER again, then button 0 and hold it until the sensor touches the surface to automatically set the height.
 
* 3. Set home. Move the machine with the arrow buttons 2, 4, 6, 8 and place it at the point where you want your zero. Press SET HOME (button № 11) and ENTER to set home for your file.
 
* 3. Set home. Move the machine with the arrow buttons 2, 4, 6, 8 and place it at the point where you want your zero. Press SET HOME (button № 11) and ENTER to set home for your file.
 
* 4. Set speed and power. In MENU (button № 15) choose Params_2d by pressing ENTER. Set speed (X Y feedrate) and power for your material according to the table.
 
* 4. Set speed and power. In MENU (button № 15) choose Params_2d by pressing ENTER. Set speed (X Y feedrate) and power for your material according to the table.
Line 377: Line 453:
 
* 8. To continue press ENTER.
 
* 8. To continue press ENTER.
  
==What not to do==
+
 
* Do not use materials that are not suitable for laser cutting! Ask the FabLab operators if you're not sure about your material.
+
 
* Do not stand on the side of the machine! Only in the front. The machine can move suddenly and quickly and can hit you.
+
<gallery widths=300 heights=300 mode=packed style="text-align:center">
* Do not continue cutting if something is going wrong! For example: if there is flame or a lot of smoke or it's not cutting or the material is melting. Pause the machine and call a FabLab operator.
+
File:IMG 20160419 134015.jpg| Original 0,0 point
* Do not change the material on the remote! It has to be "cardboard" always.
+
File:IMG 20160419 134145.jpg| Set the material thikness
 +
File:IMG 20160419 134418.jpg| Set Home
 +
File:IMG 20160419 134514.jpg| Touch sensor
 +
File:IMG 20160419 134858.jpg| speed and power
 +
</gallery>
 +
 
 +
 
  
 
==Advanced commands==
 
==Advanced commands==
* To make a test on a new material you can cut a small square or circle. Set the surface, set home on the place that you're not using, set speed and power that you want to try and then go to MENU, select Cut_utils, choose a square or any other shape, set dimensions and press GO.
+
* To make a test on a new material you can cut a small square or circle. Set the surface, set home on the place that you're not using, set speed and power that you want to try and then go to MENU, select Cut_utils, choose a square or any other shape [https://www.tabloidharga.com/ hp terbaru murah], set dimensions and press GO.
 
* After you paused the cutting you can navigate with arrows and choose Params 2d to change any settings before continuing.
 
* After you paused the cutting you can navigate with arrows and choose Params 2d to change any settings before continuing.
 
* I you need to adjust something while cutting: press PAUSE, then cancel the job, do whatever you need (reset the surface, move to continue from another place, etc.) Then to continue your cutting press SHIFT, GO, ENTER, GO.
 
* I you need to adjust something while cutting: press PAUSE, then cancel the job, do whatever you need (reset the surface, move to continue from another place, etc.) Then to continue your cutting press SHIFT, GO, ENTER, GO.
 +
 +
==Maintenance==
  
 
==Downloads==
 
==Downloads==
 +
• [[Media:Multicam_Laser_User_Manual.pdf]]: User manual
  
 
• [[Media:EnRoute Instructions.pdf]]: how to prepare and send your files to the big laser cutter using EnRoute.
 
• [[Media:EnRoute Instructions.pdf]]: how to prepare and send your files to the big laser cutter using EnRoute.

Latest revision as of 15:13, 22 January 2018

Multicam 2000 Laser Cutter

Technical specifications

  • Slew speed: 800”/min (0.33 m/sec) in X axis, 2400”/min (1 m/sec) in Y axis
  • Cut speed: 800”/min (0.33 m/sec)
  • Repeatability: +/- 0.001” (0.025 mm)
  • Raster speeds up to 1800”/min (0.8 m/sec) using up to 256 gray scale with up to a 1200 DPI resolution
  • Precision servo drives with helical rack and pinion and linear ball bearing guide ways on the X and Y-axis
  • Ball lead screw and linear ball bearing guides ways on Z axis
  • Gantry clearance 1.875” (48 mm)
  • Z axis stroke 3.25” (82 mm)
  • Y axis stroke 60” (1524 mm) and 80” (2032 mm)
  • X axis stroke 50” (1270 mm), 100” (2540 mm), 120” (3048 mm),144” (3658 mm), 168” (4267 mm), and 240” (6096 mm)

Health & Safety

  • Do not use materials that are not suitable for laser cutting! Ask the FabLab operators if you're not sure about your material.
  • Do not stand on the side of the machine! Only in the front. The machine can move suddenly and quickly and can hit you.
  • Do not continue cutting if something is going wrong! For example: if there is flame or a lot of smoke or it's not cutting or the material is melting. Pause the machine and call a FabLab operator.
  • Do not change the material on the remote! It has to be "cardboard" always.

Materials and configuration

Wood:

  • Plywood is a manufactured wood panel made from thin sheets of wood veneer. It is one of the most widely used wood products. It is flexible, inexpensive, workable, re-usable, and can usually be locally manufactured.
  • Medium-density fibreboard (MDF) is an engineered wood product formed by breaking down hardwood or softwood residuals into wood fibres, often in a defibrator, combining it with wax and a resin binder, and forming panels by applying high temperature and pressure. MDF is denser than plywood.


0.5mm

CUT

  • Speed: 100
  • Power: 52

ENGRAVE

  • Speed: 100
  • Power: 15

3mm

CUT

  • Speed: 30
  • Power: 190

ENGRAVE

  • Speed: 70
  • Power: 60

Plywood:

4mm

CUT

  • Speed: 40
  • Power: 180

Bent Plywood:

5mm

CUT

  • Speed: 90
  • Power: 130

ENGRAVE

  • Speed: 110
  • Power: 40

MDF

4mm

CUT

  • Speed: 30
  • Power: 185

ENGRAVE

  • Speed:
  • Power:

4mm

CUT

  • Speed: 35
  • Power: 150

ENGRAVE

  • Speed: 60
  • Power: 50

5mm

CUT

  • Speed: 20
  • Power: 185

ENGRAVE

  • Speed: 60
  • Power: 50

6mm

CUT

  • Speed: 20
  • Power: 220

ENGRAVE

  • Speed: 60
  • Power: 60

7mm

CUT

  • Speed: 15
  • Power: 260

ENGRAVE

  • Speed: 60
  • Power: 60

10mm

CUT

  • Speed:13
  • Power: 330-340

ENGRAVE

  • Speed: 60
  • Power: 60

RASTER

  • Speed: 600
  • Power: 80

12mm

CUT

  • Speed: 15
  • Power: 370

ENGRAVE

  • Speed: 50
  • Power: 60

12mm

CUT

  • Speed: 15
  • Power: 380

ENGRAVE

  • Speed: 50
  • Power: 60

13mm

CUT

  • Speed: 10
  • Power: 370

15mm

CUT

  • Speed: 5
  • Power: 375

ENGRAVE

  • Speed: 50
  • Power: 70

IN HIGH DENSITY WOOD SUCH AS MDF THE MAXIMUM THICKNESS IS 15 mm

Poplar Plywood / Contraplacat Pollancre

4mm

CUT

  • Speed: 35
  • Power: 150

ENGRAVE

  • Speed: 90
  • Power: 30

5mm

CUT

  • Speed: 20
  • Power: 185

ENGRAVE

  • Speed:
  • Power:

10mm

CUT

  • Speed: 20
  • Power: 375

ENGRAVE

  • Speed: 90
  • Power: 30

15mm

CUT

  • Speed: 5
  • Power: 375

ENGRAVE

  • Speed:
  • Power:

25mm

CUT

  • Speed: 22
  • Power: 255

ENGRAVE

  • Speed: 100
  • Power: 60

RASTER

  • Speed: 500
  • Power: 150

Cardboard:

  • Cardboard is a generic term for a heavy-duty paper of various strengths, ranging from a simple arrangement of a single thick sheet of paper to complex configurations featuring multiple corrugated and uncorrugated layers.

1mm

CUT

  • Speed: 100
  • Power: 80

1.5mm Grey

CUT

  • Speed: 70
  • Power: 100

2mm Grey

CUT

  • Speed: 110
  • Power: 115

ENGRAVE

  • Speed: 100
  • Power: 80

3mm Grey

CUT

  • Speed: 50
  • Power: 90

ENGRAVE

  • Speed: 100
  • Power: 35

1mm Black

CUT

  • Speed: 90
  • Power: 90

4mm Rippled

CUT

  • Speed: 100
  • Power: 150

ENGRAVE

  • Speed: 100
  • Power: 65

6mm Rippled

CUT

  • Speed: 100
  • Power: 160

Acuarela

CUT

  • Speed: 100
  • Power: 96

ENGRAVE

  • Speed: 100
  • Power: 48

Cartulins Común / Generic Cardboard

CUT

  • Speed: 120
  • Power: 90

ENGRAVE

  • Speed: 200
  • Power: 46

Metacrilato/Methacrylate:

  • Poly(methyl methacrylate) (PMMA) is a transparent thermoplastic, often used as a light or shatter-resistant alternative to glass. It is sometimes called acrylic glass. Chemically, it is the synthetic polymer of methyl methacrylate.

2mm

CUT

  • Speed: 12
  • Power: 290

3mm

CUT

  • Speed: 20
  • Power: 90

3mm Verde Opal

CUT

  • Speed: 45
  • Power: 112

4mm

CUT

  • Speed: 10
  • Power: 85

ENGRAVE

  • Speed: 120
  • Power: 80

5mm

CUT

  • Speed: 15
  • Power: 100

5mm Blanco Opal

CUT

  • Speed: 33
  • Power: 200

6mm

CUT

  • Speed: 40
  • Power: 200

8mm

CUT

  • Speed: 15
  • Power: 275

ENGRAVE

  • Speed: 120
  • Power: 160

10mm

CUT

  • Speed: 10
  • Power: 270

ENGRAVE

  • Speed: 110
  • Power: 40

Polypropylene:

  • Polypropylene (PP), also known as polypropene, is a thermoplastic polymer used in a wide variety of applications including packaging, textiles (e.g., ropes, thermal underwear and carpets), stationery, plastic parts and reusable containers of various types, laboratory equipment, loudspeakers, automotive components, and polymer banknotes.

0.5mm

CUT

  • Speed: 90
  • Power: 90

ENGRAVE

  • Speed: 90
  • Power: 60

0.8mm

CUT

  • Speed: 90
  • Power: 140

ENGRAVE

  • Speed: 110
  • Power: 40

1.5mm

CUT

  • Speed: 70
  • Power: 350

ENGRAVE

  • Speed: 90
  • Power: 90

Fabrics

Cotton

CUT

  • Speed: 90
  • Power: 15

ENGRAVE

  • Speed: 70
  • Power: 40

Suede

RASTER

  • Speed: 600
  • Power: 32

Felt/Fieltro

CUT

  • Speed: 60-70
  • Power: 110

Other:

Plastico dos capas con aire 4mm / Plastic 2 layers with air

CUT

  • Speed: 90
  • Power: 200

Acrylic 3mm

CUT

  • Speed: 40
  • Power: 170

Plastic sheets welding

ENGRAVE

  • Cut pressure 6
  • Pierce pressure 6
  • Power 80
  • Pierce power 80
  • Speed 30

How to prepare and send files

  • 1. Open EnRoute. If it's already open – go straight to step 2
  • 2. Open a new file ( File - New ) and set your sheet size (width/heigh in mm, thickness is not important)
  • 3. Import your .dxf file: File – Import – find your file
  • 4. Make sure that your drawing is inside the red border. If you need to scale or move your drawing: select everything and press F2 on the keyboard
  • 5. Select everything and go to Transform – Merge selection… and click OK
  • 6. If you are using two strategies (engraving and cutting) harga tablet terbaru then go to Layers ( Setup - Layers ) and turn the engraving layer ON and the cutting layer OFF
  • 7. Select all and click on the 'Engraving...' button (Toolpath - Engraving), in the drop-down menu select your Strategy – 'eng' and click OK. You will see the generated paths for your design
  • 8. Go to Layers again and switch your cutting layer ON and the engraving one OFF
  • 9. Select all and go to Engraving again but this time choose 'cut' in the drop-down menu
  • 10. Switch all the layers ON. You will see all your paths together
  • 11. Click the 'Output option' ( Machining - Output ) icon. Go to the 'Tool Order' section and make sure that 'engrave' is the first. If not – drag it up (click on the left box next to the number when the cursor will be an arrow to drag it up). If you have smaller pieces inside bigger pieces (holes, openings, etc.) then in 'Object Order' check 'Inside out'. Also check 'Small parts first'. Press 'To File'
  • 12. Save your file inside 'Dnc files' folder. Use one of the existing folders (MAA, FabAcademy, etc.). You can also create your own folder
  • 13. Done! Your file is sent to the machine

Notes

    • Bring your files in .dxf 2004 format so that you can import them directly to EnRoute.
    • You are not allowed to edit your files on this computer.
    • Do not open EnRoute multiple times, you can just open a new file in the same window.
    • If you have engraving and cutting you should have them in different layers.
    • Do not change material thickness.
    • All the dimensions are in millimeters. Your file units have to be millimeters.
    • If you have a grid put all the horizontal elements in one layer and all the vertical ones – in another.
    • If you are using AutoCAD or Grasshopper: use Rhino command 'Make2D' in all your layers separately.
    • Your file has to be flat (on 0 in Z axis).
    • Your home is in the lower left edge of your sheet and has to be in 0, 0, 0.

How to turn on the machine

  • On the control panel:
    • Turn System to 'ON'
    • Turn Laser to 'ON'
    • Turn Shutter to 'OPEN'
    • Turn Mode to 'RUN'
    • Fume collector to 'ON'
    • All the light should be on



  • On the wall:
    • Turn on the main compressor (there's a small box on the wall with two blue caps and two red caps: the switches inside this box have to be up)
  • On the machine:
    • Turn on the internal Ventilator(There's a small switch on the far rear of the machine)
  • On the remote:
    • SHIFT + HOME to home the machine (SHIFT is button № 20 and HOME is button № 1)


How to cut

  • 1. Place your material on the bed of the machine. The X axis is the longer part of the laser cutter and the Y axis is the sorted one. Home (0,0,0) is on the lower left corner.
  • 2. Set material thickness and surface height. Press SET SURFACE (button № 6) and ENTER (button № 30) and set the thickness of your material. The values are in millimeters sepeda gunung murah. Press ENTER again, then button 0 and hold it until the sensor touches the surface to automatically set the height.
  • 3. Set home. Move the machine with the arrow buttons 2, 4, 6, 8 and place it at the point where you want your zero. Press SET HOME (button № 11) and ENTER to set home for your file.
  • 4. Set speed and power. In MENU (button № 15) choose Params_2d by pressing ENTER. Set speed (X Y feedrate) and power for your material according to the table.
  • 5. Find your file. By pressing button № 16 you will enter the DNC files folder on the computer. Use the up and down arrows to find your file and choose it by pressing ENTER.
  • 6. Start the job. Press GO (button № 10) twice.
  • 7. If something goes wrong hit PAUSE to stop the machine (button № 5).
  • 8. To continue press ENTER.



Advanced commands

  • To make a test on a new material you can cut a small square or circle. Set the surface, set home on the place that you're not using, set speed and power that you want to try and then go to MENU, select Cut_utils, choose a square or any other shape hp terbaru murah, set dimensions and press GO.
  • After you paused the cutting you can navigate with arrows and choose Params 2d to change any settings before continuing.
  • I you need to adjust something while cutting: press PAUSE, then cancel the job, do whatever you need (reset the surface, move to continue from another place, etc.) Then to continue your cutting press SHIFT, GO, ENTER, GO.

Maintenance

Downloads

Media:Multicam_Laser_User_Manual.pdf: User manual

Media:EnRoute Instructions.pdf: how to prepare and send your files to the big laser cutter using EnRoute.

Media:MultiCam Instructions.pdf: how to turn on and use the machine.

Media:MultiCam Settings.pdf: settings for different material types and thickness.