Shopbot ATC PRS Alpha 3 Axes Milling machine

From Fab Lab Bcn WIKI
Revision as of 11:27, 9 November 2018 by Sujal23.ks (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Shopbot MTC PRS Alpha 3 Axes Milling machine - 2.49m x 1.27m x 0.2m


Technical Specifications

Dimensions:

2.49m x 1.27m x 0.2m

Health & Safety

CAM

  • 2D and 3D - RhinoCAM

After creating your milling strategy in RhinoCAM, it has to be transformed into a format that is readable by the shopbot's control system. The piece of software performing this task is called a postprocessor. Be sure to select the correct postprocessor ("Shopbot MTC") as well as the expected file extension (.sbp) in RhinoCAM when exporting your milling program.

MCS

  • ShopBot 3

Selecting the Right Bit for the Job

Milling Tools: A milling bit (also called milling cutter or end mill) is a tool used in CNC or hand-operated milling machines to remove material in a controlled manner to obtain a desired shape. This is usually done by moving the rotating tool sideways (laterally) through the material, thus cutting chips off the workpiece. Most milling bits can also cut in the direction of the tool axis, like a drilling bit. Vice-versa however, a drilling bit is designed to cut only axially to create cylindrical holes, and cannot be used for milling.

Bit material: Router bits are made from a variety of materials. The most common are solid carbide, carbide-tipped steel, and high-speed steel. Both solid carbide and carbide- tipped are good choices. We do not recommend using high-speed steel bits as they dull quickly and must be re-sharpened.

Flute type: There are four basic flute types: Straight, spiral up-cut, spiral down-cut, and compression. Each type has its own advantages and disadvantages, which are outlined in the chart below.

Schermata 2017-01-13 alle 17.01.41.png

Parameters: Feeds and Speeds

A challenge of getting a good CNC cut is in selecting the best bit, best cutting speed (feed rate) and router/spindle RPM (speed of rotation). Bits, feeds, and speeds are a critical part of machining and should be fully understood before deviating from recommended settings. Bits choice is important in chip load, which is a representation of the size of the chips produced during cutting. The goal is to get the maximum chip load possible to increase productivity, reduce heat, and prevent premature dulling. When chip load is too small, bits will get too hot and dull quicker. When chip load is too high, the tool will deflect creating a bad surface finish and, in extreme cases, chip or break the bit.

Optimising feed rates and speeds: 1. Start off using an RPM derived for the chip load for the material being cut (see charts). 2. Increase the cutting speed (feed rate) until the quality of the part’s finish starts to decrease or the part is starting to move from hold downs. Then decrease speed by 10%. 3. Decrease RPM until finish deteriorates, then bring RPM back up until finish is acceptable. 4. This optimises RPM and speed to remove the largest possible chips.

Feeds and Speed:

  • PLYWOOD


Flat 6mm, 1 flute

RPM: 13000

Plunge: 1000

Travelling clearance plane: 4000

Rest of the parameters:2000

Step down: 4mm max (always depending on the diameter of the tool)


  • FOAM

Flat 6mm, 1 flute

RPM: 12000

Plunge: 2000

Travelling clearance plane: 4000

Rest of the parameters:3500

Step down: 20mm max (always depending on the diameter of the tool)


  • CHIPBOARD

Flat 6mm, 1 flute

RPM: 12500

Plunge: 1000

Travelling clearance plane: 4000

Rest of the parameters:2000

Step down: 4mm max (always depending on the diameter of the tool)

Parameters are given by ShopBot

Schermata 2017-01-13 alle 16.45.07.png

Schermata 2017-01-13 alle 16.51.02.png

Schermata 2017-01-13 alle 16.53.13.png

Schermata 2017-01-13 alle 16.54.38.png

Schermata 2017-01-13 alle 16.55.34.png

Schermata 2017-01-13 alle 16.56.29.png

Use of SHOPBOT

-Always wear safety glasses when operating the ShopBot or observing the machine when it is in use.

-Never leave the machine when it is in operation.

-If you need a bathroom break, the machine can be paused by pressing the Space Bar on the control PC keyboard.

-Make sure the bed of the machine is clean before use. Inform us if it is not clean.

-Securely fasten your material to the bed of the machine. Consult us every time you are faced with a different, challenging or unusual work-holding scenario.

-Perform command “C3” Homing routine to establish the true machine home X-0 Y-0 (in the machine coordinates system)

-Jog X, Y to your personal Work Home coordinates, ie: the corner of your material & the X,Y origin of your drawing.

-Take a photo of the Control PC screen or take note of the machine Mesin Cuci Toshiba 1 Tabung coordinates system to your chosen Work Home position. Example: X - 105.499, Y - 145.376 (do not worry about Z yet). Work Home X Y coordinates are simply offset measurements from the true Home (X-0, Y-0) of the Machine.

-Zero work coordinates to X-0 Y-0

-Install tool in collet/tool holder + install tool/tool holder on spindle.

-Use command ”C2” & follow Mesin Cuci Panasonic prompts on the PC screen (You will place the Z-0 plate directly under the tool on your material & place the Alligator Clip onto the collet nut on the tool holder) to set the Z-0 of your home position coordinates. You now have all 3 of your X, Y & Z work home coordinates loaded into the CNC system.

-Load part file, to choose the file you need to launch, you will see your “G-Code” which you generated in RhinoCam on the screen.

-Visually check again the machine bed to ensure all tools have been removed and that material is securely fastened to the bed.

-Start in ShopBot software, follow prompts.

-Start the spindle with the green button on the ShopBot remote.

-Monitor the machine closely until the machine stops. Laser Cutters and CNC Routers have a high risk of fire if left unattended.

-If you need to pause the machine, press the Spacebar on the PC Keyboard. The machine will pause, then follow the prompts to restart or end the process.

-Emergency stop (E-stop) buttons are located in 2 places: On your remote, next to the Control PC, and On the end of the Y - Axis gantry. The Emergency Stop buttons are large, round Red buttons which will completely shut-down the machine.

-Remove the tool-holder & tool from the spindle and store it in the tool-holder rack.

-Clean the machine and your work area completely after you have removed your material.

-Skeletons and scraps created during the process should be cut up & placed in the recycling cart.

Important commands

Set Z zero

Run command C2. Put the metal plate under the machine head and connect the alligator grip to the tool head. Run Enter. The machine will go down and adjust its Z zero. Done.

Set XY zero

Run command C3. The machine will move. Wait. Done.

Change a toolpath tool

Run command 72 (press CN and then 72). The machine will leave its tool on its tool holder and will go to look for the new tool. Once the new tool is load the machine will move to the Z tool distance area in the toolpath. Connect the aligator grip to the tool head. The machine will go down and save the tool length. Done.

External Links

Rhinocam tutorials

Maintenance

Downloads