Difference between revisions of "ZCorp"

From Fab Lab Bcn WIKI
Jump to: navigation, search
m
(Maintenance)
Line 58: Line 58:
 
*See the ZPrint help for questions on the hardware specifications and for the specific software functionality.
 
*See the ZPrint help for questions on the hardware specifications and for the specific software functionality.
 
*[http://www.zcorp.com/en/Products/3D-Printers/spage.aspx ZCorp 3D-Printers web site]
 
*[http://www.zcorp.com/en/Products/3D-Printers/spage.aspx ZCorp 3D-Printers web site]
 +
 +
==Maintenance==
 +
===Only for advanced users===
 +
*Check that printer cartidges are clean. Replace cartidge number 1 by switching its position with the unused cartidges 0, 2 and 3 until all 4 cartidges were used.
 +
*Check that cleaning unit is clean and cleaning solution injector is not obstruded.
 +
*

Revision as of 16:34, 30 September 2011

Technical specifications

  • Printable volume: 250mm, 350mm, 200mm (width, depth, height).
  • Layer thickness: 0,0875 to 0,125mm.
  • Color 3D Printer: mostly used in monochrome mode.

CAM

  • Models can be generated by every software capable of exporting STL files.
  • Check 3D model validity before printing!
    • The volumes should be closed.
    • No naked edges.
    • Coherent normal direction for all the closed volumes (normals pointing outside).
    • Exporting single objects in every STL-file is recommended for better nesting in multiple-object prints.

Tools

  • Tools here

Materials and configuration

  • zp150 white, high resolution printing powder.
  • zb60 clear binder.

Machine workflow

  • Turn on the computer.
  • Turn on the machine.
  • Check the binder level. Fill all four tanks with binder at least over the binder extraction pipes at the back side of the tanks. Don't fill them too much since the binder ages in the tank.
  • Close the caps softly, don't apply pressure.
  • Check the cleaning tank levels at the center bottom part of the machine: the left one (cleaning liquid) should be almost full and the right one (residual liquid) should be empty or almost empty.
  • Check the powder recycling can (bottom right side of the machine). Use this powder in order to fill the printing bed.
  • Prepare the printing bed.
    • 1. Take the machine offline pressing the 'online' button.
    • 2. Open the machine hood.
    • 3. Move down the material container pressing the left down arrow button (Feed) and fill it with printing powder. Remove the air in the powder shaking carefully with the tools provided (inside the bottom left compartment).
    • 4. Flatten and compress the powder once the container is full.
    • 5. Bring up the printing bed pressing the right top arrow (Build). The bed should stay a few millimeters below the top level of the container frame.
    • 6. Flattening!!??
    • 7. Close the machine hood.
  • Put the machine online pressing the 'online' button.
  • Run the ZPrint software.
  • Open your STL file, select the units for your model, and the powder type (ZP150). The STL file should be a proper closed volume model with coherent normals.
  • Move, scale and rotate the model as you want in order to optimize the printing process. Try to foresee the difficulties that may arise in the removal process as the printed parts can be very fragile.
  • Take a look at the 2D mode in order to check if the material distribution is like you expect it to be.
  • Go to 'Print setup' and select the proper printer, powder type and layer thickness (default to 0,0875mm).
  • Print the file (Ctrl+P).
  • Control the process and make sure that the binder is beeing distributed homogeneously without 'dry stripes'. If this stripes apear, some maintenance or replacement of the printing heads should take place.
  • A dialog window in ZPrint shows you the elapsed printing time and estimates the overall duration of the process.
  • Once the printing process has finished, take the machine offline and lower the material container (left down arrow) and remove the material sorrounding the printed objects.
  • Once freed from most of the powder, carefully place the printed pieces on a tablet and put all into the powder recovering station.
  • Turn on the compressor and the vacuum cleaner and clean the printed objects until no loose powder sticks on them.
  • Take the pices out of the recovering station and lightly spray them with destillated water to harden them.
  • Alternatively, if you need strong durable objects, you can infiltrate them with super glue.
  • Let the pices dry in a safe place.
  • Finally, clean both the printer and the powder recovering station with the vacuum cleaner, and refill the bed with powder.

Important commands

  • Important commands here

External links

  • See the ZPrint help for questions on the hardware specifications and for the specific software functionality.
  • ZCorp 3D-Printers web site

Maintenance

Only for advanced users

  • Check that printer cartidges are clean. Replace cartidge number 1 by switching its position with the unused cartidges 0, 2 and 3 until all 4 cartidges were used.
  • Check that cleaning unit is clean and cleaning solution injector is not obstruded.