Difference between revisions of "Troteclaser"
From Fab Lab Bcn WIKI
| Line 18: | Line 18: | ||
*Join the geometry | *Join the geometry | ||
[[File:Join.jpg| 700 × 402 pixels]]<br><br> | [[File:Join.jpg| 700 × 402 pixels]]<br><br> | ||
| − | * | + | *Check the scale of the drawing , make sure you are in millimeters and that your material fits in the laser. |
[[File:Scale.jpg| 700 × 402 pixels]]<br><br> | [[File:Scale.jpg| 700 × 402 pixels]]<br><br> | ||
| − | * | + | *Seldup command selects duplicate lines. Keep in mind that is there are more than one lines the laser cutter will pass more times over the same place. |
[[File:3SelDup.jpg| 700 × 402 pixels]]<br><br> | [[File:3SelDup.jpg| 700 × 402 pixels]]<br><br> | ||
| − | * | + | *Make2d if you import your drawing from other programs other than rhino and to make sure that everything is on 0 in Z plane. |
[[File:4Make2D.jpg| 700 × 402 pixels]]<br><br> | [[File:4Make2D.jpg| 700 × 402 pixels]]<br><br> | ||
*Change object layer : hairline | *Change object layer : hairline | ||
| Line 28: | Line 28: | ||
[[File:4LayerColour.jpg| 700 × 402 pixels]]<br><br> | [[File:4LayerColour.jpg| 700 × 402 pixels]]<br><br> | ||
[[File:4ColourSelection.jpg| 700 × 402 pixels]]<br><br> | [[File:4ColourSelection.jpg| 700 × 402 pixels]]<br><br> | ||
| − | |||
| − | |||
| − | |||
| − | |||
====Printing==== | ====Printing==== | ||
| − | *Ctrl+p : Print | + | *Ctrl+p : Print |
| + | [[File:4WindowsPrint.jpg| 700 × 402 pixels]]<br><br> | ||
| + | *Properties | ||
| + | [[File:5Print.jpg| 700 × 402 pixels]]<br><br> | ||
| + | |||
| + | |||
===Job control=== | ===Job control=== | ||
Revision as of 16:05, 20 March 2015
Contents
Precaution
- Never leave the laser device unattended while the system is operating.
- Always have a fire extinguisher available, as the laser beam can ignite flammable materials.
- Do not put any flammanle materials in the inside of the device or in the immediate surroundings of the device.
- Be aware of all Laser safety stickers on the machine and follow them.
- The system must be used only by authorized and trained personnel.
- Avoid electrostatic charging during cable connections / plug-in.
- Do not start the Laser machine without an adequate exhaust system.
- In case of a broken lens: avoid direct skin contact and inhaling.
- "EMERGENCY-STOP": on any risk: LIFT THE COVER LID!
Procedures on the softwares
Rhino
Geometry
- Join the geometry
- Check the scale of the drawing , make sure you are in millimeters and that your material fits in the laser.
- Seldup command selects duplicate lines. Keep in mind that is there are more than one lines the laser cutter will pass more times over the same place.
- Make2d if you import your drawing from other programs other than rhino and to make sure that everything is on 0 in Z plane.
- Change object layer : hairline
Printing
- Ctrl+p : Print
- Properties
Job control
The Machine
Accessories
- Focus Tool
- Cone
- Allen Key set 1.5 - 10mm
- 2 Wrenches
- Lens cleaning tissues
- Optics cleaning tissues
- AC power cord
The lengths
| Colours | Focal (mm) | Thickness material Used |
|---|---|---|
| Red | 1.5 | Very fine |
| Black | 2 | Used mainly |
| Pink | 2.5 | Thick |
Cleaning optics
- Do not touch directly the lens during the operation.
- Pour on it a drop of the specific product : "Lens clens".
- Clean it with the appropriate electrostatic tissues : "Edmund Industrial Optic".
Vacuum
| Accrylic | Not Compress Air |
| Rubber | Compress Air |
| Wood | Compress Air |
