Difference between revisions of "Troteclaser"

From Fab Lab Bcn WIKI
Jump to: navigation, search
 
(33 intermediate revisions by 3 users not shown)
Line 1: Line 1:
[[Category:Machines]]
+
[[Category:Old Machines]]
 +
 
 +
[[File:Machines 8.jpg| thumb |Laser cutter Trotec Speedy 400]]
  
 
==Precaution==
 
==Precaution==
 +
 
* '''Never leave the laser device unattended while the system is operating.'''
 
* '''Never leave the laser device unattended while the system is operating.'''
 
* Always have a fire extinguisher available, as the laser beam can ignite flammable materials.
 
* Always have a fire extinguisher available, as the laser beam can ignite flammable materials.
Line 11: Line 14:
 
* In case of a broken lens: avoid direct skin contact and inhaling.
 
* In case of a broken lens: avoid direct skin contact and inhaling.
 
* "EMERGENCY-STOP": on any risk: LIFT THE COVER LID!
 
* "EMERGENCY-STOP": on any risk: LIFT THE COVER LID!
 
+
<br>
 +
[http://wiki.fablabbcn.org/Material_laser Material Laser Cut]
 +
<br>
 +
<br>
 
==Procedures on the softwares==
 
==Procedures on the softwares==
 
 
===Rhino===
 
===Rhino===
 
====Geometry====
 
====Geometry====
*Join the geometry
+
* Join the geometry
 
[[File:Join.jpg| 700 × 402 pixels]]<br><br>
 
[[File:Join.jpg| 700 × 402 pixels]]<br><br>
*Check the scale of the drawing , make sure you are in millimeters and that your material fits in the laser.
+
* Check the scale of the drawing , make sure you are in millimeters and that your material fits in the laser.
 
[[File:Scale.jpg| 700 × 402 pixels]]<br><br>
 
[[File:Scale.jpg| 700 × 402 pixels]]<br><br>
*Seldup command selects duplicate lines. Keep in mind that is there are more than one lines the laser cutter will pass more times over the same place.
+
* Seldup command selects duplicate lines. Keep in mind that is there are more than one lines the laser cutter will pass more times over the same place.
 
[[File:3SelDup.jpg| 700 × 402 pixels]]<br><br>
 
[[File:3SelDup.jpg| 700 × 402 pixels]]<br><br>
*Make2d if you import your drawing from other programs other than rhino and to make sure that everything is on 0 in Z plane.
+
* Make2d if you import your drawing from other programs other than rhino and to make sure that everything is on 0 in Z plane.
 
[[File:4Make2D.jpg| 700 × 402 pixels]]<br><br>
 
[[File:4Make2D.jpg| 700 × 402 pixels]]<br><br>
*Change object layer : hairline
+
* Change object layer : hairline
 
[[File:Hairline.jpg| 500 × 202 pixels]]<br><br>
 
[[File:Hairline.jpg| 500 × 202 pixels]]<br><br>
 
[[File:4LayersColour.jpg| 700 × 402 pixels]]<br><br>
 
[[File:4LayersColour.jpg| 700 × 402 pixels]]<br><br>
Line 30: Line 35:
 
|-valign="top"
 
|-valign="top"
 
|[[File:4ColourSelection.jpg| 700 × 402 pixels]]
 
|[[File:4ColourSelection.jpg| 700 × 402 pixels]]
|{{Grossir|<br>Engrave <br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut|facteur=1.5}}
+
|<br>Engrave <br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut<br>Cut
 
|}
 
|}
<br><br>
+
<br>
  
 
====Printing====
 
====Printing====
*Ctrl+p : Print  
+
* Ctrl+p : Print  
[[File:4WindowsPrint.jpg| 700 × 402 pixels]]<br><br>
+
[[File:4WindowPrint.jpg| 4WindowsPrint ]]<br><br>
*Properties
+
* Properties
 
[[File:5Print.jpg| 700 × 402 pixels]]<br><br>
 
[[File:5Print.jpg| 700 × 402 pixels]]<br><br>
 
+
[[File:5Preference.jpg| 700 × 402 pixels]]<br><br>
 
+
* Material Database
 
+
[[File:5MaterialDataBase.jpg|Material]]<br><br>
 +
*Process options
 +
[[File:5Process options.jpg|Process options]]<br><br>
 +
[[File:5Valid.jpg|Valid]]<br><br>
 +
* Set the view
 +
[[File:Settheview.jpg|Set the view]]<br><br>
 +
* Drag the square to define your print window
 +
[[File:PrintWindow.jpg|Print Window]]<br><br>
 +
* Press enter and once you come back to the previous screen clic on print.
 +
<br>
 
===Job control===
 
===Job control===
 +
[http://www.troteclaser.com/en-US/Support/Documents/JobControl-Manual-EN.pdf JobControl Manual]
 +
<br>
 +
* Selection of your file
 +
[[File:Selection.jpg|Selection]]<br><br>
  
 +
<br><br><br>
  
 +
==The Machine : Trotec Speedy 400==
 +
[http://www.troteclaser.com/en-US/Support/Documents/Speedy-300-Manual-EN.pdf Operation Manual]
 +
===Characteristics===
 +
{| class="wikitable"
 +
|-
 +
| Overall dimensions (W x D x H)
 +
| 1400 * 950 * 1070 mm
 +
|-
 +
| Working area
 +
| 1000 * 610 mm
 +
|-
 +
| Max. height of workpiece
 +
| 305 mm
 +
|-
 +
| Max. processing speed
 +
| 355 cm / second, acceleration 4g
 +
|-
 +
| Accuracy
 +
| Addressable accuracy: 5 microm<br> Static repeat accuracy: < +/- 15microm
 +
|-
 +
| Mechanical design
 +
| Fully enclosed chassis with double safety interlock system laser safety class, <br>CE coñpliant maintenance-free, brushless DC servo motors<br>InPack-Technology
 +
|-
 +
| Laser Design
 +
| Sealed-Off CO2 laser<br> from 40 - 120 Watt
 +
|-
 +
| Weight
 +
| Approx. 300kg (depending on laser power)
 +
|}
  
 
==The Machine==
 
 
===Accessories===
 
===Accessories===
 
* Focus Tool
 
* Focus Tool
Line 57: Line 103:
 
* AC power cord
 
* AC power cord
  
===The lengths===
+
 
 +
===The lens===
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 76: Line 123:
 
| Thick
 
| Thick
 
|}
 
|}
 +
[http://www.troteclaser.com/en-US/Laser-Machines/Accessories/Options/Pages/Focus-Lenses.aspx Focus Lenses for Trotec Laser Machines]
  
 
===Cleaning optics===
 
===Cleaning optics===
Line 95: Line 143:
 
| Compress Air
 
| Compress Air
 
|}
 
|}
 +
 +
===Turn on the machine===
 +
* Turn the key.
 +
* Clean and insert the lens in the laser head : the curved portion above.
 +
* Move the head with the arrows on the machine.
 +
* Use the focus for [http://bismilah.xyz/pialadunia piala dunia streaming] positionning the table.
 +
* When the lid is closed, a light flashes at a reduced frequency.
 +
* Turn on the vacuum, if it is necessary.
 +
* On "Job control", connect the machine and align your document with the target thanks the following commands :
 +
[[File:7tool.jpg|tool]]
 +
* Then, play.

Latest revision as of 18:46, 11 May 2018

Laser cutter Trotec Speedy 400

Precaution

  • Never leave the laser device unattended while the system is operating.
  • Always have a fire extinguisher available, as the laser beam can ignite flammable materials.
  • Do not put any flammanle materials in the inside of the device or in the immediate surroundings of the device.
  • Be aware of all Laser safety stickers on the machine and follow them.
  • The system must be used only by authorized and trained personnel.
  • Avoid electrostatic charging during cable connections / plug-in.
  • Do not start the Laser machine without an adequate exhaust system.
  • In case of a broken lens: avoid direct skin contact and inhaling.
  • "EMERGENCY-STOP": on any risk: LIFT THE COVER LID!


Material Laser Cut

Procedures on the softwares

Rhino

Geometry

  • Join the geometry

700 × 402 pixels

  • Check the scale of the drawing , make sure you are in millimeters and that your material fits in the laser.

700 × 402 pixels

  • Seldup command selects duplicate lines. Keep in mind that is there are more than one lines the laser cutter will pass more times over the same place.

700 × 402 pixels

  • Make2d if you import your drawing from other programs other than rhino and to make sure that everything is on 0 in Z plane.

700 × 402 pixels

  • Change object layer : hairline

500 × 202 pixels

700 × 402 pixels

700 × 402 pixels
Engrave
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut
Cut


Printing

  • Ctrl+p : Print

4WindowsPrint

  • Properties

700 × 402 pixels

700 × 402 pixels

  • Material Database

Material

  • Process options

Process options

Valid

  • Set the view

Set the view

  • Drag the square to define your print window

Print Window

  • Press enter and once you come back to the previous screen clic on print.


Job control

JobControl Manual

  • Selection of your file

Selection




The Machine : Trotec Speedy 400

Operation Manual

Characteristics

Overall dimensions (W x D x H) 1400 * 950 * 1070 mm
Working area 1000 * 610 mm
Max. height of workpiece 305 mm
Max. processing speed 355 cm / second, acceleration 4g
Accuracy Addressable accuracy: 5 microm
Static repeat accuracy: < +/- 15microm
Mechanical design Fully enclosed chassis with double safety interlock system laser safety class,
CE coñpliant maintenance-free, brushless DC servo motors
InPack-Technology
Laser Design Sealed-Off CO2 laser
from 40 - 120 Watt
Weight Approx. 300kg (depending on laser power)

Accessories

  • Focus Tool
  • Cone
  • Allen Key set 1.5 - 10mm
  • 2 Wrenches
  • Lens cleaning tissues
  • Optics cleaning tissues
  • AC power cord


The lens

Colours Focal (mm) Thickness material Used
Red 1.5 Very fine
Black 2 Used mainly
Pink 2.5 Thick

Focus Lenses for Trotec Laser Machines

Cleaning optics

  • Do not touch directly the lens during the operation.
  • Pour on it a drop of the specific product : "Lens clens".
  • Clean it with the appropriate electrostatic tissues : "Edmund Industrial Optic".

Vacuum

Accrylic Not Compress Air
Rubber Compress Air
Wood Compress Air

Turn on the machine

  • Turn the key.
  • Clean and insert the lens in the laser head : the curved portion above.
  • Move the head with the arrows on the machine.
  • Use the focus for piala dunia streaming positionning the table.
  • When the lid is closed, a light flashes at a reduced frequency.
  • Turn on the vacuum, if it is necessary.
  • On "Job control", connect the machine and align your document with the target thanks the following commands :
tool
  • Then, play.